The performance specifications of Mitsubishi cc-link terminal strip type input module 16-point AJ65SBTB1-16D are as follows:

[Input type] DC24V input

[Input form] Positive and negative common terminal common type (drain type, source type common type)

[Enter number of points] 16 points

[Insulation method] Optical coupler insulation

[Rated input voltage] DC24V

[Rated input current] about 7 mA

[Operating voltage range] DC19.2~26.4V (fluctuation rate is within 5%)

[Maximum number of points simultaneously] 100%

[ON voltage/ON current] above 14V/3.5nA

[OFF voltage/OFF current] below 6V/1.7mA

[Input resistance] about 3.3k Ω

[Response time] OFF ->ON/ON ->OFF is less than 1.5ms (at DC24V)

[Common terminal mode] 16-point 1 common terminal (2-point) (terminal strip type 1-wire type)

[Number of occupied stations] 32 points are allocated to 1 station (16 points are used)

[I/O module power supply]

Voltage: DC20.4~26.4V (fluctuation rate is within 5%)

Current: below 30mA (DC24V, when all points are ON)

[Noise intensity] Through the DC type noise voltage 500VP-P noise width 1 μ S. Noise generated by noise simulator with noise frequency of 25~60Hz

[Withstand voltage] DC external terminal summary - grounding room AC500V for 1 minute

[Insulation resistance] DC external terminal summary - DC500V insulation resistance meter between grounding measures 10M Ω

[Protection level] IP2X

[External connection mode]

. Communication part, I/O module power supply part:

7-point 2-segment terminal block [transmission circuit, I/O module power supply, FG]

M3 * 5.2 Tightening torque 59~88N? Cm The number of insertion of applicable crimping terminals is less than 2

. Input and output power supply part, input and output part:

18-point direct installation terminal strip [input/output power supply, I/O signal]

M3 * 5.2 Tightening torque 59~88N? Cm The number of insertion of applicable crimping terminals is less than 2

[Module mounting bolts]

. Round M4 bolt with flat washer (tightening torque range 79~108N. cm)

. It can be installed through DIN rail and in 6 directions

[Applicable DIN rail] TH35-7.5Fe, TH35-7.5A1 (based on JIS C 2812 standard)

[Applicable to crimping terminals]

RAV1.25-3 (based on JIS C 2805 standard) Applicable wire size: 0.3~1.25mm2

Applicable wire size of V2-MS3, RAP2-3SL and TGV2-3N: 1 25~2.0mm2

[Weight] 0 18kg

1. Mitsubishi full series PLC, frequency converter, human-machine interface, servo system.

2. Xinjie PLC, frequency converter, human-machine interface and servo system.

3. Delta PLC, frequency converter, human-machine interface and servo system.

4. Wellington human-machine interface and Hytec human-machine interface.

Mitsubishi servo motor HG-JR15K1MB;

Mitsubishi servo motor HG-JR11K1MB;

Mitsubishi servo drive MR-J4-11KA

Mitsubishi servo drive MR-J4-11KB

Mitsubishi servo drive HG-KR-23J with oil seal

Mitsubishi servo store HG-KR053

Mitsubishi servo motor HG-KR73BJ with oil seal

Mitsubishi servo motor HG-SR102BJ with oil seal

Mitsubishi MR-J4-15KB servo driver

Mitsubishi PLC (programmable controller) A, R, Q, L, CC-LNK, FX3SA, FX3G, FX3G, FX3U, FX5U and other series;

Mitsubishi frequency converter A840, E840, F840, E740, D740, D720 series; Mitsubishi touch screen GT2000 series; Mitsubishi servo motor JE, J4 series.

Mitsubishi programmable controller: FX3GA, FX3GE, FX3G, FX3U, FX3UC, FX2NC, A, Q, CC-LINK remote module and other series

Mitsubishi variable frequency governor: FR-L700, FR-A700/500, F700/500, E700/500, D700/500, S500 and other series;

Man-machine interface: GOT2000, GOT16, GOT15, GOT12, GOT11, GOT10, A900GOT, F900GOT and other series;

AC servo system: MR-J4, MR-JE, MR-J3, MR-J2S, MR-E, MR-ES and other series;

Tension control system: LE-40MTA (B), LD-FX, LD-50PAU and other series:

Low-voltage electrical appliances: S-N, TH-N, etc.