Cooling Tower Filler, buy 12mm 15mm 19mm pitch PVC plastic filter block PVC tricking filter on China Suppliers Mobile

Product Details

Product Details

12mm 15mm 19mm pitch PVC plastic filter block PVC tricking filter

PVC tricking filter is made of PVC or PP plain plate.

They are hot pressed in the certain mould, and then be produced according to different design and be used in different cooling towers, especially in the industrial cooling tower. As we all know, the main usage of the cooling tower fill is a media located in the bottom or middle of water treatment or industrial cooling tower.

waste water treatment PVC tricking filter is a modular PVC corrugated media that is specifically designed for fixed
film biological treatment applications. With a minimum void to volume ratio of 95%, PVC filter block allows for uniform redistribution of wastewater and air while maximizing contact between the biomass and the wastewater.

PVC filter modules are composed of thermoformed PVC sheets that are UV protected and resistant to rot, fungi, bacteria, acids, and alkalines commonly found in wastewater. The PVC compound is non-toxic to microorganisms and specifically formulated to resist long-term creep and cracking under continuous loading.

Material	Sheet Spacing	Flute Angle	Media Pack Sizes: Depth(D), Width(W), Length(L)			Pitch	Sample
PVC/PP	0.75 in (19 mm)	31°	Minimum	Maximum	Standard
PVC/PP	0.75 in (19 mm)	31°	PVC/PP			D: 6 in (153 mm) W: 6 in (153 mm) L: 1 ft (305 mm)	D: 24 in (610 mm) W: 24 in (610 mm) L: 12 ft (3658 mm)	D: 12 in (305mm) or 24 in (610mm) W: 12 in (305mm) or 24 in (610 mm) L: 4 ft (1220 mm), 6 ft (1829 mm), 8 ft (2439 mm) or 10 ft (3048 mm)

Black PVC filter

Green PVC filter

White PP fills

Product Introduction

12mm 15mm 19mm pitch PVC plastic filter block PVC tricking filter

• Bevel Tips promotes drainage at fill pack interfaces. Note: Packs are always installed with Bevel Tips at bottom of pack.
• Patented "MA"(Mechanical Assembly) Technology for glue-free packs.
• Engineered microstructure for improved water distribution and thermal mixing
• High thermal performance
• Improved water distribution
• Proprietary edge trim that directs water to both sides of sheet
• Material meets Cooling Tower Institute (CTI) Standard 136
• Available in PVC

Product Processing

Product Packing

12mm 15mm 19mm pitch PVC plastic filter block PVC tricking filter

For LYOW fills, loose sheets or glued blocks are both ok. If loose sheets, it will save so much shipping space,

If glued blocks, you can directly fill your cooling tower when you receive your order.

When will the cooling tower need replace the cooling tower fill?

1. Increased Energy Consumption When fill isn’t doing its job properly the water flowing through the cooling tower isn’t getting cooled. This means that to do the job the cooling tower is designed to do at your location it will take more electricity to do the same job. While electricity prices to change if you’ve seen a marked increase in your bill you might check the cooling tower and the cooling tower fill.

2. Calcium Buildup Makeup water contains a lot of dissolved solids and one of them in calcium. Calcium from hard water will build up in the fill causing blockages. When your fill is clogged the air and water cannot pass through and the cooling tower will not work. In some cases the fill can be cleaned, in others the buildup is severe enough to require cooling tower fill replacement.

3.Uneven Distribution of Water All cooling towers are designed to maximize the contact between the water and air running through them. When the water isn’t being distributed properly because the fill is damaged or clogged it dramatically impacts the performance of the cooling tower. Much more energy will need to be used to get the necessary cooling needed for your industrial application or HVAC system.

4.Damaged Support Grids Support grids are the structure that holds your fill in place. If water has degraded the structure, or there have been other types of damage your fill will not be performing correctly. This can be a cause for fill packs to sag, warp, or simply fall out of place. If your fill isn’t sitting where it should be, it isn’t doing its job. Invest in your cooling tower maintenance and ensure that your support grids are up to par.

5. Cooling Tower Maintenance There are a number of important cooling tower maintenance tasks to keep your cooling tower running at optimum efficiency. Fill is one of the most important elements for the performance of the cooling tower. It is where the hot cycle water goes to be cooled by the air flowing through the fill. If your fill has buildup, clogging, or is damaged we can help!