MODEL

LPS-100-15

OUTPUT

DC VOLTAGE

15V

RATED CURRENT

6.7A

CURRENT RANGE

0 ~ 6.7A

RATED POWER

100.5W

RIPPLE & NOISE (max.)   Note.2

100mVp-p

VOLTAGE ADJ. RANGE

13.5 ~ 18V

VOLTAGE TOLERANCE   Note.3

±2.0%

LINE REGULATION    

±0.5%

LOAD REGULATION    

±1.5%

SETUP, RISE TIME

800ms, 50ms/230VAC         1200ms, 50ms/115VAC at full load

HOLD UP TIME (Typ.)

20ms/230VAC         20ms/115VAC at full load

INPUT

VOLTAGE RANGE

88 ~ 132VAC / 176 ~ 264VAC auto switch         248 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

80%

AC CURRENT (Typ.)

2.3A/115VAC         1.5A/230VAC

INRUSH CURRENT (Typ.)

COLD START 30A/115VAC         60A/230VAC

LEAKAGE CURRENT

<1mA / 240VAC

PROTECTION

OVER LOAD

105~ 140% (+24V: above 6.5A) rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

18 ~ 21V

Protection type : Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP.

-10~+60°C (Refer to derating curve)

WORKING HUMIDITY

20~90% RH non-condensing

STORAGE TEMP., HUMIDITY

-20~+85°C, 10~95%RH

TEMP. COEFFICIENT

±0.05%/°C (0~50°C)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY&EMC

(Note 4)

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC   I/P-FG:1.5KVAC    O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100MOhms/500VDC/25°C/70%RH

EMC EMISSION

Compliance to EN55011, EN55022 (CISPR22) Class B, EN61000-3-2,-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A

OTHERS

MTBF

203.6Khrs min.      MIL-HDBK-217F (25°C)

DIMENSION

222*62*32mm (L*W*H)

PACKING

0.45Kg; 24pcs/12.5Kg/1.39CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.

5. If the input range 85V-89V, the output load is changed from 0A-rated load, There will be reduced 20V for 1second (LPS-100-24).

6. Mounting holes M1 and M2 should be grounded for EMI purposes.