MODEL

RPS-160-48

OUTPUT

DC VOLTAGE

48V

RATED CURRENT (20.5CFM)

3.25A

CURRENT RANGE (convection)

0 ~ 2.3A

CURRENT RANGE (20.5CFM)

0 ~ 3.25A

RATED POWER (convection)   Note.7

113.4W

RATED POWER (20.5CFM)   Note.8

161W

RIPPLE & NOISE (max.)    Note.2

250mVp-p

VOLTAGE ADJ. RANGE

CH1: 43.2~ 52.8V

VOLTAGE TOLERANCE   Note.3

±2.0%

LINE REGULATION    

±0.5%

LOAD REGULATION    

±1.0%

SETUP, RISE TIME

1800ms, 30ms/230VAC           3500ms, 30ms/115VAC at full load

HOLD UP TIME (Typ.)

16ms/230VAC/115VAC at full load

INPUT

VOLTAGE RANGE      Note.6

90 ~ 264VAC         127 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR (Typ.)

PF>0.93/230VAC         PF>0.98/115VAC at full load

EFFICIENCY (Typ.)

88%

AC CURRENT (Typ.)

2A/115VAC        1.1A/230VAC

INRUSH CURRENT (Typ.)

COLD START 35A/115VAC         70A/230VAC

LEAKAGE CURRENT      Note.9

Earth leakage current<200uA / 264VAC, Touch current < 100uA/264VAC

PROTECTION

OVER LOAD

105 ~ 135% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

55.2 ~ 64.8V

Protection type : Shut down o/p voltage, re-power to recover

OVER TEMPERATURE

110°C5V),105°C(12V,15V,24V,48V) (TSW1 : detect on heatsink of power transistor)

95°C(5V),90°C(12V,15V,24V,48V) (TSW2 : detect on heatsink of power transistor)

Protection type : (TSW1)Shut down o/p voltage, recovers automatically after temperature goes down

Protection type : (TSW2)Shut down o/p voltage, re-power on to recover

FUNCTION

5V STANDBY (G model)

5VSB : 5V at 0.6A without fan, 0.8A with fan 20.5CFM ; tolerance ±2%, ripple : 50mVp-p(max.)

PS-ON INPUT SIGNAL (G model)

Power on: PS-ON = "Hi" or " > 2 ~ 5V" ; Power off: PS-ON = "Low" or " < 0 ~ 0.5V"

POWER GOOD / POWER FAIL

500ms>PG>10ms         PF>1ms

REMOTE SENSE

5 ~ 15V

ENVIRONMENT

WORKING TEMP.

-20~+70°C (Refer to derating curve)

WORKING HUMIDITY

20 ~ 90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40~+85°C, 10~95%RH

TEMP. COEFFICIENT

±0.03%/°C(0~50°C)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.eachalong X, Y, Z axes

SAFETY&EMC

(Note 4)

SAFETY STANDARDS

ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1 approved

WITHSTAND VOLTAGE

I/P-O/P:4KVAC     I/P-FG:2KVAC O/P-FG:1.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25°C/70% RH

EMCEMISSION

Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A

OTHERS

MTBF

230.5K hrs min   MIL-HDBK-217F (25°C)

DIMENSION

127*76.2*34.6mm (L*W*H)

PACKING

0.32Kg; 36pcs/12.5Kg/0.79CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives.

5. HS1,HS2 & HS3 can not be shorted.

6. Derating may be needed under low input voltages. Please check the derating curve for more details.

7. The rated power includes 5Vsb at 0.6A.

8. The rated power includes 5Vsb at 0.8A.

9. Touch current was measured from primary input to DC output.

10. Suitable for BF application with appropriate system consideration.