Name: tbe power digital generator 50000 watt pure sine wave ac inverter
Brand: TOP GIN
Availability: InStock

Product Details

Current flux vector inverter

[Performance]

TG600 has a full magnetic flux vector current control characteristics, based on modern control theory, the magnetic flux vector detection and control technology, the direct control of the motor torque at low speed (1% of rated speed), even without the use of PG closed loop also provides high starting torque and trouble-free operation, when the increase in PG control, even provide full torque at zero speed control.

[Feature]

1. A low speed when not using the PG high starting torque speed control range 1:00 (1: 1000 with PG)

2. reliable torque control

TG600 through precise torque limit function to control the output torque. In the event of failure, but also to ensure the safe operation without impact.
TG600 proved its durability and perfect performance in heavy-duty mechanical applications.

3. excellent servo response

PG closed loop case with magnetic flux vector control

4. precise control of a wide range of speed control

TG600 even under load change conditions with full speed range features high-precision operation.
From light to heavy cross-speed control (without PG)
(Velocity resolution of ± 0.2% 0-100% load (± 0.02 with PG)

5. 4kinds of control integration. For any application

Contained in a single drive in four kinds of control modes: standard V / F control with PG closed loop V / F control, no pass inductor current magnetic flux vector control with PG closed loop flux vector control. TG600 by simply selecting parameters can be used for a wide range of applications, with high precision mechanical servo drive motor system until much pain. Can help users to standardize on a single inverter for all applications.
Set sensorless current vector control inverter magnetic plastic factory.
But when the need for multi-motor drive, you can set to V / F control mode, according to a PG motor, can achieve high-precision vector operation.
When PG control, you need to use the PG speed control card.
Low speed high torque required for continuous operation, please use the company's special motors.

[Specification ]

Control Characteristics

Control mode	Sine wave PWM mode selectable by parameter setting four control modes (1) V / F control (2) V / F control attached PG feedback (3) Current speed sensorless flux vector control (4) flux vector current control PG feedback
Starting torque	150% / zero rpm (when not accompanied by PG 150% / 1Hz)
Speed control range	1: 1000 (when the PG is not attached 1: 100)
Speed control accuracy	± 0.02% (when not attached PG ± 0.2%)
Speed response	30Hz (33ms) (PG when not attached 5Hz (200ms))
Torque limit	By parameter settings can be independently set four quadrants
Torque Control	Four-quadrant operation possible (Forward Motor / regenerative reversal electric / resuscitation)
Torque response	40Hz (25ms) (PG when not attached 20Hz (50ms))
Frequency control range	0.01~400Hz
Frequency control accuracy	Digital signal: ± 0.01% (-10 ℃ ~ + 40 ℃) analog signal: ± 0.1% (25 ℃ ± 10 ℃)
Frequency setting resolution	Digital signal: 0.01Hz Analog signals: 0.03Hz / 60Hz * (12bit)
Frequency output resolution	0.01Hz
overload	150% of rated current 1 minute PER10MIN @ 40 ℃ above
Analog frequency setting signal	DC-10~+10V,0~10V(20KΩ)4 ~ 20mA(250Ω)
Acceleration and deceleration time	0.01 to 6000.0 seconds (four groups of acceleration, deceleration time set individually)
Brake torque	Approximately 20% additional Brake up to 150%
Run / stop setting	Operator, RS232, RS485 / 422, the control circuit terminals, 12/16 BiT binary signal
Protective function
Motor protection	Electronic thermal relay protection, under phase protection
Instantaneous overcurrent	200% of the rated current of the motor free stop
Fuse protection	Motor stops after the fuse blows freely
Overload	Motor freedom stops at more than 150% of the rated output current of about 1 minute PER10MIN @ 40 ℃
Overvoltage	Main circuit DC voltage of about 220V class 400V, 440V 800V class about free stop over motor
Low Voltage	Main circuit DC voltage of about 220V class 200V, 440V 400V class about freedom following motor stop
Instantaneous power compensation	After the operation mode selection within 2Sec blackouts continue to operate (external capacitor)
Fin overheat	Thermocouple Protection
Stall prevention	Acceleration and deceleration, stall prevention operation
Ground protection	Electronic circuit protection
Charging indicator	he main circuit DC voltage above 50V charging indicator "light"
Vibration	20Hz below 1G, 20 ~ 50Hz when 0.2G
Efficiency	Pf>0.95&η>0.95@40℃ above

[SIZE]