Control axis: X axis, Z axis, Y axis, c axis; C axis can be used as CS axis; Optional 4-axis 3-linkage

Interpolation mode: positioning (G00), straight line (G01), arc (G02, G03)

Position command range: metric: - 999999.99mm -999999.99mm、minimum command unit: 0.0001mm

Feed rate: 0 ~ 200% 21 level real-time adjustment

Maximum cutting feed rate: 15000 mm / min

Fast magnification: F0, 25%, 50%, 100% four level real-time adjustment

Maximum fast speed: 60000 mm / min

Feed per revolution: 0.01mmr ~ 500mm (spindle encoder shall be installed)

Acceleration and deceleration mode: front acceleration and deceleration (linear and S-type) and rear acceleration and deceleration (linear and exponential type)

Electronic gear ratio: frequency doubling 1 ~ 65535, frequency division 1 ~ 65535

Hand pulse feed: three gears of 0.001, 0.01 and 0.1mm 

Display: 8.4-inch digital screen

Display of machining track and preview of programming track

System a instruction format is adopted, with a total of 39 g codes, including fixed cycle code and complex cycle code

Support level 5 subroutine call and user macro program call

support Sentence type Program (macro a, macro b)

Suitable tool rest: General Electric tool rest, Liuxin tool rest and DELTA servo tool rest

Tool change mode: MD automatic absolute tool change or manual relative tool change, forward rotation tool selection and reverse locking

Tool setting mode: fixed-point tool setting, trial cutting tool setting, return to mechanical zero point tool setting

Tool position signal input mode: direct input

S2 digit (o gear control) / S5 digit (analog output)

Spindle encoder: the number of encoder lines can be set (100 ~ 999999p / R)

Transmission ratio between encoder and spindle: (1-255): (1-255)

Spindle magnification: 50% ~ 120%, a total of eight levels of real-time repair and adjustment

2 channels of 0 ∨ - 10 ∨ analog voltage output, Support dual spindle control

-10v-10v analog voltage output parameters are optional

Specify with address m and 2 digits, and the M function can be customized

Internal system m instruction (non redefinition): program end m2 and M30; program stop M00: select Stop M01, program call M98 ; subroutine end M99

Coolant start and stop, lubrication start and stop, MD automatic mode control chuck clamping / loosening, and control the advance
and retreat of tailstock

Common thread (following spindle)

Single head / multi head metric and inch straight thread, taper thread and end face thread, equal pitch thread and variable pitch thread

The length, angle and speed characteristics of thread tailing can be set by program and parameters

Thread pitch: 0.001mm-500mm (metric system) 0.06 tooth inch - 25400 tooth inch (British system)

Pitch error compensation: the compensation interval and compensation origin can be set, and one-way screw compensation or two-way screw compensation can be selected

Reverse clearance compensation: fixed frequency or speed up and down compensation can be set, and different reverse clearance compensation is supported for G0 and G1

Tool compensation: 99 groups of tool length compensation and tool tip radius compensation

PLC processing speed: 1US / step; 8000 steps at most; 10 basic instructions and 35 functional instructions

L / O unit input / output: 32 / 32, expandable

1-4 PMC axes can be selected

Subroutine: editable, supporting quintuple subroutine nesting

Program capacity: 57mb, 400 programs

Format: relative absolute mixed programming

Support background editing and programming program track preview

Mode selection: edit, automatic, MD |, zero return, manual, single step, manual pulse

Operation control: single section, skip section, empty operation, auxiliary lock, program restart, hand pulse interruption, single step interruption and manual intervention

Emergency stop

Hardware travel limit

Data backup and recovery

RS232: bidirectional transmission of part programs, parameters and other files, supporting PLC programs

USB: USB flash disk file operation, support PLC program, system software USB flash disk upgrade

Network interface: two-way transmission of part programs, parameters and other files and connection with computer (PC) can monitor the system processing program, coordinate position, number of processing pieces, cutting time and other information

Switching power supply: rs-pb2 (supplied together, installed and connected)

Drive unit: GSK GR series tool holder controller:

Tool holder controller GSK TB tool holder controller