Wet Type Peanut Peeling Machine
Negotiable /Set
Min.Order:1 Set
Zhengzhou LONGER Machinery Co, Ltd
Wet Type Peanut Peeling Machine|Automatic Wet Peanut Peeler Equipment
The Working Principle of Wet Type Peanut Peeling Machine
The soaked peanut rice bean kernels are rotated into the three-wheel fixed-power drum tires by shaking the raw materials, and the raw skin incisions are subjected to blade cutting through the infeed wheel blades on the induction wheels, and then the materials are peeled off to remove the rice, the kernels, and the beans. Press into the hopper and hopper discharge, threw away the thrown leather jacket.
Installation and Commissioning
Mounted on flat ground, ground screw fixation, or more than 10mm legs padded rubber mats.
Required by the electric motor, the power is on, tap the switch, check the direction of rotation is correct (see the rotation direction of the V-belt big wheel mark), add water after the power is turned on, the machine is running five minutes after the start of work (the machine must be kept for too long the correct direction of rotation by hand one to two laps before turning the boot).
Note
1.Non-inversion
2.Equipment must be installed the ground wire
3.All parts of the screws should be firmed again before the new machine turn on,especially the parts of the set screws should be pay more attention to.
4.Bearings must be greased once a week
5.Should to keep the machine clean and do the cleaning periodical.
Attach:Parts Schematic of the peeling machine
Technical Parameters
Project | Peanut | Almond | Broad Bean | Soybean |
Capacity(kg/h) | 200-220 | 200-220 | 300 | 150 |
Peeling rate(%) | 98±1 | 92-95 | 92-95 | 92±1 |
Broken rate(%) | 3±1 | 3±1 | 3±1 | 2 |
Whole kernel rate(%) | 85-95 | 88±2 | 76±2 | - |
Input Power | 0.75kw(220V, 380V optional) | |||
Dimensions | Length * width * height=1080×800×1100(mm) |
Failure Analysis and Elimination
Fault Phenomenon | Failure Cause | Solution |
Low Peeling Rate | 1.Soak a short time, the water temperature is too low, there are differences between varieties of raw materials | Note the time, adjusting the water temperature |
2.Blade damage or blockage on knife around | Replace the blade, cleaning knife around and between the tire skin of bean ,sundries | |
3.Feed wheel is too high (skin, rice, beans from the blade too high, do not cut the skin incision) | Reduced feed wheel or knife to adjust the height (distance from the turret tire fixing screws within 4-6mm) | |
4.Feed wheel gap is too large or severe tire wear | Transfer a small gap, replacement the rubber wheel | |
Too many rice, kernels, beans on the skin after peeling | The feed wheel is too high and skin removing roller axis distance is too large | Adjust low the feed wheel, let the skin attached to the shaft squeeze |
Too many skin on the rice, kernels, beans | The feed wheel is too low,resulting squeeze the skin of the inner shaft left tire | Adjust high the feed wheel, So crowded leather shaft with rubber tires, the wheels are expected to maintain good contact |
Rejection does not turn the wheel or damaged skin | Adjustments, changing skin throwing wheel | |
After installing the chain, dumped skin throw wheel rotation in the wrong direction | Reinstall the chain | |
Too much rice,bean without skinning outflow by the bailing tank
| Inconsistent with the induction of broken or induction of induce belt | Replacement or adjustment |
The size of the raw material | Grading the raw material | |
Feed tire in contact with the sides of the screen blocking plate is too short | More shifting plate | |
High breaking rate after peeling
| The rubber wheel gap is too small | Rising the gap of the rubber wheel |
Raw soaking time beyond the technological requirements (time too long) | According to the process specified time soaking | |
Beans thrown from the rubber wheel | Feed rate too large | Reduce the feeding quantity |
Too slow of the outlet tank and the feeder screen | Feeding screen loose fixtures | Inspection, fixed, repair and replace the gum cover |
Reversing device fracture | ||
Severe or too tight pouches worn shock |