Product Details

Specifications

Stainles steel bearing GE10E
1.Gcr15 material
2.self-lubricating
3.bear large load
4.ISO:9001:2000

Stainless steel oscillating bearing rod ends GE10E

Definition of Stainles steel bearing GE10E

Ball joints are the pivot between the wheels and the suspension of an automobile. Ball joints play a critical role in the safe operation of an automobile's steering and suspension. Ball joints can also be found in most linkage systems for motion control applications, and should not be confused with spherical rod end bearings, which are a different design.

Sealed ball joints do not require lubrication as they are "lubed for life" but standard ball joints must be lubed from time to time. It's best to inspect standard ball joints once a year. Generally speaking, standard ball joints will outlive sealed ones because eventually the seal will break, causing the joint to dry out and rust. While there is no exact lifespan that can be put on a sealed ball joint, they can fail as early as 80,000 miles. Signs of a failing ball joint start with a clicking or snapping sound when the wheel is turned and eventually turns into a squeaking sound at the end of a stop, when the gas pedal is used and/or also when hitting bumps. Another symptom could be 'thud' noises coming from front suspension when going over bumps.

If a ball joint fails, the results can be dangerous as the wheel's angle becoming unconstrained, causing loss of control. Because the tire will be at an unintended angle, the vehicle will come to an abrupt halt damaging the tires. Also, during failure, debris can damage other parts of the vehicle.

Joint bearings can bear larger load. According to their different type and structure, can bear radial load, axial load or the radial, axial co-existing union load. Because of the sphere, circle with composite materials, reason this bearing in the work can produce self-lubrication. Commonly used for low speeds swinging movement, and low speed rotating, also can be in certain Angle range be tilted movement, when supporting shaft and axis shell hole concentricity bigger when, still can work normally. Self-lubricating joint bearings used in water conservancy, specialized mechanical industries.

Quick Details of Stainles steel bearing GE10E

1.The inner and outer rings are coated with molybdenum disulphide for reduced sliding friction.

2.These spherical plain bearings have a single fractured outer race.

3.This spherical plain bearing does not have grooves and thru holes.

4.This spherical plain bearing must be properly lubricated with grease.

GE10E Spherical Plain Bearing
One Bearing

GE10E Spherical Plain Bearing is a popular item that could be used in many applications, the dimensions are 10mm x 19mm x 9mm.

Item: GE10E Ball Bearing
Type: Spherical Plain Bearing
Material: Carbon Steel
inner Diameter (ID): 10mm
outer diameter (OD): 19mm
Width/Height/thickness: 9mm
Size: 10 x 19 x 9 mm
Quantity: One Bearing
Dynamic Load Rating: 960 KGF
Static Load Rating: 5760 KGF
GE10E=GE10D0

Dimensions
d	D	B	C
10mm	19mm	9mm	6mm

Type	Rod End
Brand Name	CLUNT
Bore Size	4 - 100 mm
Model Number	GEG120ES-2RS GEG140ES-2RS SI15D SI17D SI20D SI25D U4 U5 U6 U8 U10 U12
Place of Origin	Jinan, China (Mainland)
Seals type	Open/z/zz/rs/2rs etc.
Material	Gcr15 or Carbon steel
Precision	P4 P5 P6 etc.
Model number	GEG120ES-2RS GEG140ES-2RS SI15D SI17D SI20D SI25D U4 U5 U6 U8 U10 U12
Port:	Shenzhen
Packaging Details:	Single box+carton+pallet or Customer requirement
Delivery Time:	within 5 days
Payment Terms:	L/C,D/P,T/T,Paypal
Supply Ability:	10000 Set/Sets per Month

Joint bearings application	Self-lubrication ball joint bearing is a kind of special structure of sliding bearings.Joint bearings is widely applied in engineering, hydraulic oil cylinder metalforming machine
Joint bearings classification	Such as SB type, type, GE, CF series,and the amount and type of other types of the joint bearings and fixed-end joint bearings, etc.
Number of row	single row or double row
Material	chrome steel ,stainless steel,and bearing steel
Vibration and noisy lever	Z1,Z2
Tolerance Code	ABEC-1
Packing	Single box+carton+pallet or Customer requirement

classification and features:

1. To the heart joint bearings

(1) GE... E model sheet, no lubrication oil every outer ring. Can bear radial load and any direction of smaller axial load.

(2) GE... ES type single-slit invading.this, lubrication oil groove. Can bear radial load and any direction of smaller axial load.

(3) GE... ES - 2RS type single-slit invading.this, lubrication oil groove, with seals at both. Can bear radial load and any direction of smaller axial load.

(4) GEEW... ES - 2RS type single-slit invading.this, lubrication oil groove, with seals at both. Can bear radial load and any direction of smaller axial load.

(5) GE... ESN type

Single slit outer ring, have lubrication oil groove, outer ring have check dynamic slots. Can bear radial load and any direction of smaller axial load. But the axial load by stop ring inherit, its axial load capacity reduction.

(6) GE... XSN type

A double-slit outer profile especially circle (), there is lubrication oil groove, outer ring have check dynamic slots. Can bear radial load and any direction of smaller axial load. But the axial load by stop ring inherit, its axial load capacity reduction.

(7) GE... HS type lubrication oil groove, inner ring has double half invading.this, after wearing clearance can be adjusted. Can bear radial load and any direction of smaller axial load.

(8) GE... DE1 type

Inner ring for hardened bearing steel, outer ring for bearing steel. Inner circle assembling extrusion, lubricating oil and oil hole. Inner diameter less than 15mm bearings, no lubrication oil and oil hole. Can bear radial load and any direction of smaller axial load.

(9) GE... DEM1 type

Inner ring for hardened bearing steel, outer ring for bearing steel. Inner circle assembling extrusion, bearing load bearing outer ring pressed, after the end ditch makes bearing axial fixation. Can bear radial load and any direction of smaller axial load.

(10) GE... DS type

Outer ring have assemble slots and lubricating slots. Limited to large size bearings. Can bear radial load and any direction of smaller axial load (assembly slot side can not bear the axial load).

2. Angular contact joint bearings

GAC... S-type inside and outside circle were hardened bearing steel, outer ring have tanks and oil hole. Can bear radial load and a direction (joint) axial load.

3. Thrust joint bearings

GX... S-type shaft lap and seat ring are hardening bearing steel, Seat ring have tanks and oil hole. Can bear a direction of axial load or combined load (right now the radial load value nor larger axial load value of 0.5 times).

4. Fixed-end joint bearings

(1) SI... E type is GE... E type bearings and pole terminal assembly body. With female threaded rod ends, materials for carbon steels, No lubrication oil groove. Can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(2) SA... E type is GE... E type bearings and pole terminal assembly body. Fixed-end out-of-band thread, materials for carbon steels, No lubrication oil groove, can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(3) SI... ES type is GE... ES type bearings and pole terminal assembly body. With female threaded rod ends, materials for carbon steels, Have lubrication oil groove. Can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(4) SA... ES type is GE... ES type bearings and pole terminal assembly body. Fixed-end out-of-band thread, materials for carbon steels, Have lubrication oil groove. Can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(5) SIB... S-type with female threaded rod ends, materials for carbon steels, Inner ring for hardened bearing steel, Have lubrication oil groove. Can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(6) SAB... S-type fixed-end out-of-band thread, materials for carbon steels, Inner ring for hardened bearing steel, Have lubrication oil groove. Can bear radial load and any direction less or equal 0.2 times radial load of the axial load.

(7) SQ... Type for ball head fixed-end joint bearings, fixed-end for carbon steels, Ball head for carburizing steels. Can bear radial load and any direction of smaller axial load.

Numbers of joint bearing

New modle	Old modle	d	D	width (mm)
New modle	Old modle	(mm)	(mm)	width (mm)
GE220ES	GE220ES	220	320	135
GE220ES-2RS	GE220ES-2RS	220	320	135
GE240CS-2Z	GE240CS-2Z	240	340	140
GE240ES	GE240ES	240	340	140
GE240ES-2RS	GE240ES-2RS	240	340	140
GE25C	GE25C	25	42	20
GE25ES	GE25ES	25	42	20
GE25ES-2RS	GE25ES-2RS	25	42	20