Jacketed cylindrical conical brewery fermentation tank
USD $1,200 - $15,000 /Set
Min.Order:1 Set
Jinan Tiantai Beer Equipment Co., Ltd.
Jacketed cylindrical conical brewery fermentation tank
Introduction of the conical fermentation tank
The brewery fermentation tanks can be individually temperature controlled through glycol jacket and are
mostly equipped with accessories such as overpressure and under pressure valve, CIP cleaning jet, sanitary
sample valve, manhole,etc. The design of TBE fermenters is based on our vast beer knowledge and
especially the conical fermenter bottom and the fact that we combine fermentation and maturation in the
same vessel is very important. When calculating your fermenting and lagering capacity and configuration
sufficient time for fermenting and lagering to produce quality beers must be taken into consideration.
Brewery fermentation tank is called CCT’s(Cylindrical Conical Tanks), FV’s(Fermentation Vessel), primary
fermenter unitanks as they are used both for fermenting and lagering. Fermenting is the process during which
the yeast transforms the wort into beer. Lagerings takes place after fermenting and is the time given to the
beer to stabilize and age after fermenting.
Basic specifications of our brewery fermentation tanks
Fermentation Tank Series | Volume in US Gallon | Diameter | Height |
1HL Fermentation Tank | 26US Gallon | 620mm | 1600mm |
2HL Fermentation Tank | 53US Gallon | 820mm | 1800mm |
3HL Fermentation Tank | 79US Gallon | 960mm | 1900mm |
4HL Fermentation Tank | 106US Gallon | 960mm | 2100mm |
5HL Fermentation Tank | 132US Gallon | 1010mm | 2100mm |
6HL Fermentation Tank | 159US Gallon | 1060mm | 2150mm |
8HL Fermentation Tank | 211US Gallon | 1060mm | 2550mm |
10HL Fermentation Tank | 264US Gallon | 1210mm | 2550mm |
12HL Fermentation Tank | 317US Gallon | 1360mm | 2550mm |
15HL Fermentation Tank | 396US Gallon | 1560mm | 2620mm |
20HL Fermentation Tank | 528US Gallon | 1560mm | 3100mm |
25HL Fermentation Tank | 660US Gallon | 1560mm | 3450mm |
30HL Fermentation Tank | 793US Gallon | 1760mm | 3500mm |
The brewery fermentation tank lower than 1000L:
The brewery fermentation tanks exceed 1000L:
1000L fermentation tanks:
3000L Fermentation tanks:
10000L fermentation tanks:
The specifications of the brewery fermentation tanks
* Interior shell: 304 stainless steel, thickness 3mm
* Exterior shell: 304 stainless steel, thickness 2mm
* Interior and exterior finish bright polish to 0.6~0.8, hygiene surface
* 60 degree cone bottom, other angles can be specified during the design process
* Combined drain extensions and beer port in cone are standard
* 25% headspace, unless a different volume is requested
* Top manway or side manway door
* Dual zone in sidewall and cone dimple cooling jacket with glycol inlet and outlet
* Polyurethane insulation thickness 80mm for cooling jacket on side and bottom
* Fully welded exterior shell
* Non welding CIP arm and rotating 360 degree reach spray ball
Manufacturing of the brewery fermentation tanks
1. Welding: We abandoned the argon gas cylinder but adopt The Central System of Argon to make sure the
TIG welding with pure argon gas shield. We also increase the using amount of gas when welding,
so the quality of the welding line is more higher.
2.Dimpling: We adopt dimple plate rather than belt for glycol jacket, since it can increase the cooling area and
improve the speed of cooling. The most important thing in brewing process is to avoid contaminating, that is to
say the most important thing in producing beer equipment is to polish the inside tanks to 0.4~0.6 μm without
dead corner.
3.Polishing: We use large-scale polishing equipment to polish the inside of the tanks -- all over the wall to
make sure there is no dead corner. And we adopted passivation and acid pickling which will make our tanks
with higher accuracy. You need not worry about there will be some bacterias remained after cleaning.
Packing and shipping of our brewery fermentation tanks
Packaging : We consider all different potential situation in the delivery, so we use every prevention measures
to avoid any potential inconvenience or trouble
a.Bulk cargo: Standard wooden case which can avoid any clash during the sea or air transportation in case of
causing damage to the surface of our products.
b. Container cargo: the equipment will be bound firmly and won’t easily swing to the side, or up, or down.
Shipping: Deliver from Qingdao port within 30-45 days after the payment
About Jinan Tiantai Beer Equipment Co., Ltd
Our company is a professional beer equipment manufacturer. We are specialized in professional design,
manufacture, installation and commissioning of various beer equipments and supporting facilities.
Our products include mashing equipment, fermentation equipment, yeast spread cultivation equipment, and
refrigeration equipment for small and medium-sized brewery, hotel, pub and etc.
Other products you may interest:
Stainless steel beer brewhouse equipment
1000 Liter stainless steel beer brewhouse
Welcome to send us inquiry for detailed cost of the brewery fermentation tanks!