High Performance High Quality Medium Modulus Multi-purpose MS Polymer Sealant
MS-50 Medium Modulus Multi-purpose MS Sealant
Product Description
MS-50 is one component multi-purpose and anti-sagging elastic MS sealant; cured by reacting with moisture in the air, to form a permanent elastomer. It’s silane-modified sealant with the advantages of polyurethane and silicone sealants. it is a flexible sealant widely recognized as with the best overall performance, can meet the needs of adhesive bonding and flexible sealing for a variety of occasions.
Applications
Used in automobiles, buses, elevators, ships, containers, tunnels, rail transit, waterproof dams, nuclear power plants, airport runways, houses, elevated, anti-smashing walls, etc., suitable for high-strength structural bonding and sealing. Suitable substrates include aluminum-plastic panels, marble, wood, concrete, PVC injection molded parts, glass, fiberglass, steel, stainless steel, and aluminum alloys (including painted).
Advantages
1.Low VOC, no silicone, without bubbles while curing, with very little odor;
2.Good wear-resistance, with a wide range of flexible bonding and durability, primer is not required;
3.It can be painted, polished, bonded and repaired in a repeated manner;
4.UV resistant, anti-aging and weathering resistance, flooding resistant and mould resistant;
5.Neutral Dealcoholize curing, no corrosion and pollution to substrates;
6.Resistant to fresh water, sea water and usually water-based cleaning agents, and has a strong bearing capacity to fuel, mineral oil, vegetable oil and animal fat and crude oil, intolerant to concentrated organic or inorganic acid/base solution or solvent ;
7.For specific requirements, we can provide relevant products and advice.
PROPERTY MS-50 | |
Appearance | White,Grey,Black homogeneous paste
|
Density (g/cm³) | 1.40±0.10 |
Tack Free Time (min) | 15~60 |
Curing Speed (mm/d) | ≥3.0 |
Elongation at break(%)
| ≥300% |
Hardness (Shore A) | 35~50 |
Tensile strength(MPa)
| ≥2.0 |
Shear Strength(Mpa) | ≥1.5 |
Sag | No sag |
Peel adhesion
| More than 90% cohesive failure |
Service Temperature ( ℃) | -40~+90 ℃ |
Shelf Life (Month) | 9 |
∎Direction for use
Tool: Manual or pneumatic plunger caulking gun
●Cleaning: Clean and dry all surfaces by removing foreign matter and contaminants such as oil dust, grease, frost, water, dirt, old sealants and any protective coating.
●For cartridge
1.Cut nozzle to give the required angle and bead size
2.Pierce the membrane at the top of the cartridge and screw on the nozzle
3.Place the cartridge in an applicator gun and squeeze the trigger with equal strength
●For sausage
1.Clip the end of the sausage and place in barrel gun
2.Screw end cap and nozzle on to barrel gun
3.Using the trigger extrude the sealant with equal strength
∎Attention of operation
●Please strictly according to the application process, any violation of the application operation may cause bonding failure. This product is innocuous after curing completely, but before
curing, please avoids contacting with eyes and skin. In case of eyes and skin contact, wash immediately and thoroughly with soap and water. If the situation is serious, please go to see a doctor immediately
∎Transport &Storage
● Transport: Keep the sealed product away from moisture, the sun, high temperature and avoid collisions.
● Storage: Keep the sealed product into cool, dry place.
● Storage temperature: 5~25℃. Humidity: ≤50%RH.
●Cartridge and Sausage :12 month.
Notice:If the temperature is higher than 40 ℃ or the humidity is more than 80%RH, the shelf life may be shorter.
Any inquiry, welcome to talk more with us cell/whatsapp:+8618321208486.