●GSK Link Industrial Ethernet bus control

●5 axis 5 linkage (straight line), minimum control accuracy 0.1 μ m. Maximum moving speed 100M / min

●Online cam function, read DXF file and generate machining program

●It supports on-line servo parameter configuration, real-time servo status monitoring and mechanical zero return without stop

●It has the functions of programming wizard and automatic programming of plane milling

●It supports I / O unit expansion and can be adapted to disc magazine, hat magazine and turret magazine

●Support secondary development of display interface (user-defined page)

●Support rigid tapping, cylindrical interpolation and indexing table control

●Support high-speed small segment program die machining

●Peripheral axis control is supported. There are 5 peripheral axis control groups in total

●Support one click breakpoint data recovery

●Support rigid tapping and roundness waveform analysis

●With torque protection function

Maximum number of control axes: 5 axes

Maximum number of linkage axes: 5 axes (linear interpolation), 2 axes (circular interpolation)

Number of PLC control axes: 5 axes

Workpiece coordinate system (G50), local coordinate system, workpiece coordinate system 1-6 (G54-G59)

Coordinate plane selection

Position instruction range: ± 9999999 × Minimum input unit

Absolute increment programming, diameter / radius programming, imperial / metric conversion, linear axis / rotary axis

It contains 69 g commands, including fast positioning, linear interpolation, arc interpolation, cylindrical interpolation, thread cutting, polar interpolation, polygon turning, rigid tapping, pause, drilling, tool compensation, macro program call, jump, cycle, tilt axis control, thread repair, etc

Fast moving speed: 0mmmn-100000mm / min

Fast magnification: F0, 25%, 50% and 100% four levels of real-time adjustment

Cutting feed rate: 0mm / min-15000mm / min

Feed rate: 0 ~ 150%, 16 levels in total, real-time adjustment

Fast moving cutting feed acceleration and deceleration: linear and S-type. The starting speed, ending speed and acceleration and deceleration time of acceleration and deceleration are set by parameters

Servo motor adapted to multi turn absolute position encoder

The absolute coordinate system is automatically restored after the machine tool is powered off

Mechanical zero return of machine tool without stop

Online modification of servo parameters

Servo status online diagnosis

Operation log, operation log and processing log

Remote monitoring and gsklink diagnostic functions

Thread types: equal pitch straight/conical/end face/arc, variable pitch straight/conical/end face/equal tip width variable guide thread

Number of threaded heads: 1-99

Thread pitch: 0.01mm-1000mm (metric thread) or 0.06 teeth/inch-2540 teeth inch (English thread)

Thread cutting acceleration and deceleration: Linear, exponential, S-type optional

Thread back: tail back length, angle and speed characteristics can be set

Spindle speed: can be given by S code or PLC signal, speed range 0rpm-999999rpm

Spindle multiplier: 50%~120% 8 levels real-time trimming

2-way 0V-10V analog voltage output to support flexible and rigid

2-way spindle encoder feedback, spindle encoder line number can be set

Tool length compensation (tool offset): 32 groups

Tool wear compensation: 32 sets

Tool life management: 32 groups (8 groups)

Tip Radius Compensation (Type C)

Knife alignment: fixed point to knife, trial to knife, reference point to knife, automatic to knife, coordinate recording function

Tool offset execution: modify coordinate mode, tool movement mode

Special M code (M00, M01, M02, M30, M98, M99), the rest of M code is defined by the PLC

Two-level PLC program, maximum 5000 steps, 1st level program refresh cycle 8ms

13 Basic directives, 44 functional directives

PLC program online display, real-time monitoring; Support for PLC warning and PLC warning

Support multi-PLC program, the current running PLC program can be selected

Basic I/O: 48 inputs/38 outputs

Extensible Serial I/O Unit (optional): IOR-21F: 24-point input, 16-point output, 2 analog voltage outputs

IOR-44F: 48-point input, 32-point output, 4 analog voltage outputs

IOR-04T: 48-point input, 32-point output voltage output interface

IOR-44T: 48-point input, 32-point output, 4 analog voltage outputs, 1 RS485/232 serial interface

Editing: Full screen editing

Editing function: program segment word retrieval, modification, deletion, copy, paste

MDI allows 10 segments to be input and run

Supports macro/subroutine calls, allowing 4-level subroutine nesting

Calculator

Assisted Programming

Track preview, graphic simulation, idle operation, machine tool lock, auxiliary function lock, single section operation, stored stroke detection

Fixed cycle, multiple fixed cycles, rigid tapping, direct input of drawing size, automatic chamfering, statement macro programming

Reverse clearance compensation: 0mm-2mm (or 0inch-0.2inch). The reverse clearance compensation mode and frequency are set by parameters

Memory pitch error compensation: a total of 1024 compensation points, and the number of compensation points of each axis is set

8.4 inches / 10.4 inches

Support Chinese, English and other languages

The processing track is displayed, the processing track is enlarged and reduced in real time, and the font of the program content can be enlarged and reduced

Position, program, tool compensation, alarm, parameter, setting, graphics, diagnosis, ladder diagram, help

Operation mode: edit, automatic, input, mechanical zero return, hand pulse / single step, manual, program zero return, hand pulse trial cut / fallback

Level 6 operation authority management

32 time limited shutdown

Program switch, parameter switch

Interruption of hand pulse and teaching

Machine tool function debugging and machine tool fault diagnosis

Regular maintenance function

USB: USB disk file operation, direct processing of USB disk files, and support PLC program and system software USB disk upgrade

RS232: bidirectional transmission of part programs, parameters and other files, import and export of screw compensation parameters, and support PLC program update

LAN: remote file transfer

Emergency stop, hardware travel limit, software travel check, data backup and recovery

48 / 38 point digital input / output interface, 2-way encoder interface, 2-way handwheel interface, 2-way spindle analog
interface, RJ45 network interface and GSK-LINK network interface

GSK 980TDi (W×H×D)

GSK 980TDi-V (W×H×D)

GSK 980TDi-H (W×H×D)

GSK 980TDi (W×H×D)

GSK 980TDi-V (W×H×D)

GSK 980TDi-H (W×H×D)