meltblown manufacturer fabric production line machine pp meltblown extruder nonwoven fabric cloth making machine

 

Product picture

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Product parameters

Machine voltage	380V
Machine power	90kw
Weight	800KG
Machine size	l1600 * W3000 * h2300 mm
Cloth width	650mm
Capacity	300kg / day

 

 

 

Machine configuration

Product name	Specifications	quantity
extruder	/	1
Screen changer	/	1
Hopper dryer	50kg	1
Suction machine	/	1
Mixing machine	650	1
mould	15kw	1
Roots blower	/	1
Heating bag	30kw	1
Net belt line	/	1
Electret holder	/	1
Electret	70kv	1
Coiler Slitter	/	1

 

 

 

Product advantages

Melt-blown non-woven process is draft the thin flow of polymer melt extruded from mold head by using high speed hot air,to form a microfiber that curdle on the mesh curtain or roller,and to be non-woven fabrics that depends on its own bonding.

 

Melt-blown non-woven fabric has the advantages of good uniformity, high filtration efficiency and strong barrier ability, mainly used in filtration materials, clothing materials, battery diaphragm materials.

 

Product features

1, polymer feed

 

This equipment is equipped with automatic vacuum suction feeding device. Generally, the polymer is made into small spherical and granular slices. When the vacuum device is opened, the raw materials can be fed into the hopper equipped with the extruder.in

 

If the material in the hopper is low, please fill it up immediately. Otherwise, the material will be broken and the melt spray cloth will become thin or not mesh.

 

2, molten extrusion

 

At the feeding end of the screw extruder, the polymer slice shall be mixed with the necessary raw materials such as additives. After mixing, the polymer slice shall enter the screw extruder and be heated to melt. Pay attention to the heating temperature

 

According to the characteristics of the raw material to be adjusted, can be in accordance with the manufacturer's recommended parameter Settings, can also be adjusted in accordance with the actual production requirements, so that the finished products to meet the use requirements.

 

3, fiber formation

 

The filtered clean melt should pass through the filter screen and then be evenly fed into the spinneret to make the extrusion amount of each spinneret consistent

 

When the volume, need to stop the machine to check whether there is a fault, check whether the filter screen is blocked, timely troubleshooting problems, so as not to damage the extrusion equipment.When eliminating extruder problems, check

 

The filter plate of the spinneret can observe whether the holes in the filter plate have impurities that cannot flow normally.The fibers are pulled out of the melt by the crosswind, the spinnerets are squeezed out of the glue, and then cooled.

 

4,electrostatic electret

 Therefore, in order to improve the filtration efficiency of the mask, the electrostatic adsorption capacity of the mask can be increased.And increase the capacity of mask electrostatic adsorption, the need to melt spray non - spinning Cloth filter material for electret treatment.After electret treatment, the surface of the fiber will be charged with a large amount of static electricity Add breathing resistance.

 

6,slitting and winding

 

There is rewinding equipment at the end of the production line.The fusion-sprayed non-woven fabric is cut and rolled up to the size required for packaging.Winding has tension control device, so that the winding material is always stable

 

Volume status.Before the rewinding is equipped with a cutting knife, which can remove the edge material, so that the packaging specifications for packaging, of course, can also be cut into the size of the product production, the distance between the cutting knife is non-woven

 

The width of the finished product, this distance can be adjusted, according to the production needs to adjust and arrange the number of cutting knive

 

Details picture

 

 

 

 

 

 

 

 

Packaging picture

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

Contact information:

 

 

 

Berry Xue ( sales manager )

 

 

 

 

 

M:  +86-18639525015;

 

T: +86-0395-5679933; F: +86-395-6665669

 

Skype: sales10-orange

 

Whatsapp: +86-18639525015

 

E:  sales10@orangecoltd.com

 

W: http://lhorange.en.china.cn

 

 

 

LUOHE ORANGE MECHANICAL EQUIPMENT CO.,LTD 

 

 

 

Office address: F16, Block 19, Fortune Plaza, Songshan Road, Luohe, Henan, China

 

Factory address: No.2, Chezhan Road, Shangqiao, Yancheng District, Luohe, Henan, China