high quality PFE95 99 Meltblown nonwoven fabrics production line | 800MM Melt blown fabrics making machine
USD $65,000 - $65,000 /Set
Min.Order:1 Set
Luohe Orange Mechanical Equipment Co., Ltd.
great quality factory price automatic 1000L 2000L RO water treatment machine
2020 hot selling Automatic Sticker Labeling Machine For Bottles Two Sides Labeling Machine
high quality Round bottle labeling machine automatic labeling machine for long label
stainless steel 304 Automatic Tabletop Plastic Glass Round Bottle Labeling Machine
Factory price Automatic square round bottle labeling machine with counting label
high quality PFE95 99 Meltblown nonwoven fabrics production line | 800MM Melt blown fabrics making machine
Product picture
Product parameters
Machine voltage |
380V |
Machine power |
90kw |
Weight |
800KG |
Machine size |
l1600 * W3000 * h2300 mm |
Cloth width |
650mm |
Capacity |
300kg / day |
Machine configuration
Product name |
Specifications |
quantity |
extruder |
/ |
1 |
Screen changer |
/ |
1 |
Hopper dryer |
50kg |
1 |
Suction machine |
/ |
1 |
Mixing machine |
650 |
1 |
mould |
15kw |
1 |
Roots blower |
/ |
1 |
Heating bag |
30kw |
1 |
Net belt line |
/ |
1 |
Electret holder |
/ |
1 |
Electret |
70kv |
1 |
Coiler Slitter |
/ |
1 |
Product advantages
Melt-blown non-woven process is draft the thin flow of polymer melt extruded from mold head by using high speed hot air,to form a microfiber that curdle on the mesh curtain or roller,and to be non-woven fabrics that depends on its own bonding.
Melt-blown non-woven fabric has the advantages of good uniformity, high filtration efficiency and strong barrier ability, mainly used in filtration materials, clothing materials, battery diaphragm materials.
Product features
1, polymer feed
This equipment is equipped with automatic vacuum suction feeding device. Generally, the polymer is made into small spherical and granular slices. When the vacuum device is opened, the raw materials can be fed into the hopper equipped with the extruder.in
If the material in the hopper is low, please fill it up immediately. Otherwise, the material will be broken and the melt spray cloth will become thin or not mesh.
2, molten extrusion
At the feeding end of the screw extruder, the polymer slice shall be mixed with the necessary raw materials such as additives. After mixing, the polymer slice shall enter the screw extruder and be heated to melt. Pay attention to the heating temperature
According to the characteristics of the raw material to be adjusted, can be in accordance with the manufacturer's recommended parameter Settings, can also be adjusted in accordance with the actual production requirements, so that the finished products to meet the use requirements.
3, fiber formation
The filtered clean melt should pass through the filter screen and then be evenly fed into the spinneret to make the extrusion amount of each spinneret consistent
When the volume, need to stop the machine to check whether there is a fault, check whether the filter screen is blocked, timely troubleshooting problems, so as not to damage the extrusion equipment.When eliminating extruder problems, check
The filter plate of the spinneret can observe whether the holes in the filter plate have impurities that cannot flow normally.The fibers are pulled out of the melt by the crosswind, the spinnerets are squeezed out of the glue, and then cooled.
4,electrostatic electret
Therefore, in order to improve the filtration efficiency of the mask, the electrostatic adsorption capacity of the mask can be increased.And increase the capacity of mask electrostatic adsorption, the need to melt spray non - spinning Cloth filter material for electret treatment.After electret treatment, the surface of the fiber will be charged with a large amount of static electricity Add breathing resistance.
6,slitting and winding
There is rewinding equipment at the end of the production line.The fusion-sprayed non-woven fabric is cut and rolled up to the size required for packaging.Winding has tension control device, so that the winding material is always stable
Volume status.Before the rewinding is equipped with a cutting knife, which can remove the edge material, so that the packaging specifications for packaging, of course, can also be cut into the size of the product production, the distance between the cutting knife is non-woven
The width of the finished product, this distance can be adjusted, according to the production needs to adjust and arrange the number of cutting knive
Details picture
Packaging picture
Contact information:
Berry Xue ( sales manager )
M: +86-18639525015;
T: +86-0395-5679933; F: +86-395-6665669
Skype: sales10-orange
Whatsapp: +86-18639525015
E: sales10@orangecoltd.com
W: http://lhorange.en.china.cn
LUOHE ORANGE MECHANICAL EQUIPMENT CO.,LTD
Office address: F16, Block 19, Fortune Plaza, Songshan Road, Luohe, Henan, China
Factory address: No.2, Chezhan Road, Shangqiao, Yancheng District, Luohe, Henan, China