Motor type | Output | Voltage | Load | Speed | Rated Torque | Efficiency |
KW | V | A | RPM | N.m | % | |
VOL-BL075B48 | 0.75 | 48 | 16.98 | 3000 | 2.39 | 92 |
VOL-BL1K0C48 | 1 | 48 | 24.5 | 2500 | 3.82 | 85 |
VOL-BL1K2C24 | 1.2 | 24 | 63.3 | 4200 | 2.73 | 79 |
VOL-BL1K2C36 | 1.2 | 36 | 39.7 | 2270 | 5.05 | 84 |
VOL-BL1K5C24 | 1.5 | 24 | 73.5 | 2590 | 5.53 | 85 |
VOL-BL1K5C72 | 1.5 | 72 | 23.5 | 3200 | 4.48 | 89 |
VIEW MORE PLS CONTACT US >>>
Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
You May Like
- 1000w 1500rpm High Efficiency Powerful brushless waterproof motor for Industrial use
- Custom 3000rpm 220vac 12.56A 4000w BLDC brushless servo dc motor
- 110V superior high torque high efficient 3000RPM 10000 rpm ac dc brushless motor
- High torque 220V 3500W 1500rpm custom direct current brushless motor
- 5v 7.4v 24v 750w magnetico permanente japan electric cart brushless dc motor
- high speed 3000rpm low power 300w brushed DC motor for industrial applications
- 1kw 2500rpm 24v waterproof quality assurance full range speed brushless dc motor
- 36v-220v 1500RPM 2000W high power brushless DC motor for auto
- Waterproof IP54 400w 12v 72v 3000rpm brushless dc motor
- low noise high efficiency 110Vac 3000rpm brushless dc motor 0.4KW
Popular Searches
Find Similar Products By Category
You May Like
- 24V 500W 3000rpm low voltage low noise brushless dc motor
- Hall effect ABC sensor 3000rpm 0.5kw 1.1kw 1.5kw 48v brushless dc motor
- 110Vac 500Watt 3000rpm 24v high torque low rpm brushless dc motor
- 220V 1.59Nm 500w brushless dc motor with hall sensors
- Optional encoder 600w 12v 1500rpm brushless dc motor
- Long lifetime 12v dc motor 3000RPM 700w brushless dc motor for Automation
- 6 kw 48v wind machin controller pcb magnet rotor brushless dc motor with differenti
- 785w 2kw 4500 rpm industri speed control hollow shaft electr vehicl mower brushless dc motor with esc
- y2-180l-4 2.2kw 24v India neodymium permanent magnet brushless dc motor for ebike
- Custom IP54 bicycle car optional controller 24v 3000rpm 3600 watts brushless dc electric motor with hall sensor
- Aluminum Frame 110Vac 600w brushless dc motor 3000rpm
- Permanent Magnets 3000rpm 220V 600w brushless dc motor
- 700w 3000RPM 24V Long lifetime small size brushless dc motor
- HFM043 220v 4500w 4.5kw 5.5kw 3000rpm vibration neodymium magnet brushless dc electric motor for car
- IEC frame 110V 3000RPM 0.7KW brushless dc motor for Automation