High Quality Semi-automatic Capsule Filling Machine JNG-255

one year warranty and lifelong technical services

♦Overview♦ 

----------------------------------------------------------------------------------------------

JNG-255 medical capsule filling machine is a new product well-designed on the basis of original capsule filling machine, which is adapted to the conditions of China. For general capsules it is a multi-purpose machine which can complete not only the capsule arranging, but also the capsule sealing.    

The product combines three machines (cap and body arranging machines, and sealing machine) into one, with the features of low price, easy operation, convenient maintenance, low power consumption, high production efficiency, and less work places. It is widely used for production of medical capsule in small pharmaceutical factories, preparation rooms of hospitals, health product factories, etc.   

♦Min Technical Data♦

---------------------------------------------------------------------------------------------

1. As the proficiency of operation varies from 30 to 50 seconds/time, 255 capsules are produced each time; and 160 thousand to 250 thousand capsules are produced in each working team.

2. Power: Arranging machine 220V±15%   50HZ

        Sealing machine 220V±15%   50HZ

3. Power consumption: less than 470 W

4. Complete set:

  The complete set includes: 1) Cap arranging machine

                        2) Body arranging machine

                        3) Sealing machine

♦ Installation and Debugging ♦

----------------------------------------------------------------------------------------------

(I) Installation

The machine can be directly put in a clean flat-floored plant for operation without mechanical installation after it is unpacked and checked to be undamaged.

 (II) Debugging

The capsule specification the machine produces has been debugged into the specification according to the order or purchased specification of the user, so that rechecking is only needed before debugging.   

1. Charging hopper (the first thing is to screw two screws on the hopper, then install the hopper on the machine, and tighten the nuts.)

2. Check each facility whether any screw is loose during the transport.  

3. After pushing the shifting plate in, check whether the plate is completely aligned with the corresponding 255 holes, and adjust the position of shifting bracket to align in necessity.  

4. As the caps fall into the holes of plate on cap arranging machine, the openings of capsules should be slightly higher than the upper surface of plate by about 0.5 mm to 1mm; as the bodies fall into the holes of plate on body arranging machine, the openings of capsules should be at the same level with the upper surface of body plate, otherwise the height of transverse baffle fixed on the vertical bracket needs to be adjusted.

Note: the upper surface of the shifting plate should be parallel to the plate.

5. The height of support bar of the conversion plate should be like that the upper side of the conversion plate is basically close to the lower side of the shifting plate when the (cap or body)  conversion plate are put into corresponding arranging machine (put without the pedal stepped). Otherwise it has to adjust the length of the two screws against the counter top inside the box and the two gland nuts on the tension bar connected to the foot lever.

6. Sealing machine: check or adjust whether the distance and parallelism between the upper side of base plate and the lower side of lifting board (turn the belt pulley of input axis on the reducer by hand to move the cam to the bottommost position) conform to the data required in Table 

♦Common fault and removal ♦

-----------------------------------------------------------------------------------------------

Table I

Distance between the base plate and lifting board

Table II

Notes: The data above shall be revised according to the practical situation.

      The above-mentioned is the data when the lifting board is at the bottom position.

Capsule Filling Machine (Figure I)

1. Hopper                                     2.Arranging machine

3.Shifting plate                                  4.Transverse baffle

5.Vertical bracket                                6.Support bar of the conversion plate

7.Power switch                                  8.Voltage regulator

9.Pedal                                         10. Electromagnet

11.Lifting board                                 12.Position switch

13.Base plate                                    14. Pull rod

15.Long guide bush                              16.Joint lever nut

17.Compressed spring bush                       18.Spring

19.Joint lever                                    20.Adjusting screw

21.Nut                                         22. Adjusting joint lever

23.Cam                                        24.Reducer

25Motor

♦Our Services♦

--------------------------------------------------------------------------------------

1)- We usually do the package with carton box and foam.
2)- We usually ship out the goods within 3 days.
3)- If the item is in stock, we will send it in 24 hours for you.
4)- DHL, UPS, FedEx, TNT are our choices. If you have a reliable shipping companies, please let me know.

1)- We will check the package and do the test before the shipment in case the purchased goods is workable.
2)- We want smooth transactions, if you have any problem, issues, concern before purchase, please let us know.
3)- Once your order from us, we will provide excellent after-service for you.
4)- If there is any damage or shortage after picked up. Please inform us immediately. 
5)- Any refund or replace for the goods purchased, please let us know first.

Yason General Machinery Manufacturing Co.,Ltd 
Address : Xiajin Road Baixiangxia Ouhai District Wenzhou city Zhejiang province China 
Tel : (00)86-791-83811092 (0086)13462818722
Skype: yasoncorporation

Should you have any questions,call me or email me,

let’s talk details.