LMS Durable Quality Galvanized Trapezoidal Wall Panel Cold Roll Forming Machine

• cold roll forming machine

   

• metal Wall Panel Cold Roll Forming Machine

   

• Durable Quality Galvanized Trapezoidal Wall Panel Cold Roll Forming Machine

   

Main Specification:

Suitable Material                                                     G.I. Coil, PPGI Coil, G245

  ii.   Material Thickness                                          0.3 - 0.6 mm

 iii.   Material Width                                                  1'220 mm

 iv.   Profile Width                                                    1'000 mm

 v.   Profile Height                                                    27 mm

 vi.   Profile Shape                                                   as drawing

II       Production Process:

 decoiling - manual shearing- roll-forming - hydraulic cutting - profile

III      Main parameters:

i    Decoiler   1 set

(1)  Working Principle                                            MANUAL

(2)  Max. Decoiling Width                                       1'250 mm

(3)  Max. Loading Capacity                                    6000 kgs

(4)  Coil's Outer Diameter                                      Ø 1,200 mm

(5)  Coil's Inner Diameter                                       Ø 508 ± 30 mm

viii   Manual Roller Shearing                                    1 set

(1)   Material                                                              Cr12 Steel

(2)   Material Surface                                                under Heat Treatment

(3)   Function: PLC is calculating profile length within roll forming. Once

material is required to change, PLC is calculating the length for total

quantity and remind operator,

production finishes and able to manual shearing material before roll forming

 so as to change material for new production. It is the advanced function for

 roof machine and good for production to save material, no waste.

ix     Main roll forming machine                           1 set 

(1)   Roll Forming Stations                                  18 Nos.

(2)   Roller's Material                                           40Cr

(3)   Roller's Main Shaft                                      Ø 75 mm, in 45# Carbon Steel, 

                                                                             Refined

(4)   Machine Side-Wall Thickness                   18 mm

(5)   Main Bearing                                               6210

(6)  Roll Forming Speed                                    8-12 meters / minute

(7)  Main Motor                                                   7.5 kw

(8)   Power Transit                                              by Gears & Chains

(9)   Driven                                                          by Main Motor

(10)Speed Adjustment                                      by Frequency Convertor

x       Hydraulic Cut-Off Device                                     1 set

(1)   Cutter Type                                                             Hydraulic Automatically Cut-                                                                                        Off Device

(2)   Cutter Composition                                                Motor, Hydraulic Pump   

                                                                                        Stand,Electromagnetic Valve

(3)   Cut-Off Mould                                                         1 Set

(4)   Cut-Off Mould Material                                           Cr12, Heat Treatment

(5)   Cut-Off Mould Material Surface Hardness            HRC 60 - 62

(6)   Cut-Off Working Pressure                                    10 MPa, Maximum

(7)   Motor                                                                       3.0 kw

xi     SIMPLE RUN OUT TABLE                    1 set

(1)   Length                                                        6 meters

xii    ELECTRONIC CONTROL SYSTEM

(1)   Electronic Control System                           By PLC, Touchable  

                                                                              Screen,Frequency Convertor, 

                                                                              Encoder, etc.

(2)   PLC                                                               Mitsubishi, Japan

(3)   Touchable Screen                                        Mitsubishi, Japan, 5.7"

(4)   Electric elements                                          Schneider, Japan

(5)   Frequency Converter                                    Mitsubishi, Japan, 5.5 kw

(6)   Encoder                                                         Omron, Japan

(7)   Power Supplier                                             380V, 50Hz, 3Phs

(8)   Length Tolerance                                          ≤ ± 2.0 mm

INSTALLATION, MAINTENANCE AND OPERATOR TRAINING

 1.     1 year guarantee for spare parts is included in quotation.

2.     The operator training in our factory is free.

3.     The technician could be sent for installation and operator training at site, but   the fee should be discussed separately.