LMS Customized galvanized steel roof sheet ridge cap roll forming machine

• ridge cap roll forming machine

   

• galvanized cap making machine

   

• steel roof sheet ridge cap roll forming machine

   

Specifications

roof ridge cap roll former
1,Decoiler 1set
2,forming machine 1set
3,PLC control
4,high quality

roof ridge cap roof ridge cap roll former

roof ridge cap roll forming machine

INTRODUCTION

LMS roll forming machine which takes the COPRA, designing software for cold rolling production and applies for the first step of rolling design, calculation, molding technique simulation, blueprint optimization and roller design to rough molding management, digital machining and quality control. LMS applies for the COPRA in the whole process. The greatness of COPRA is combined with LMS's great experience of twenty years completely and this make LMS be with might double in production for clients. Realize your dream with CORPA.

Quotation: FOB Guangzhou, China.
Metal ridge cap roll forming machine(PLC control): will be confirmed after receiving your specification & profile drawing.

Payment term:40% down payment, and 60% balance payment before shipment by T/T.
Delivery time: 85 days after 40% down payment by T/T.

? TECHNICAL PARAMETER
? METAL RIDGE CAP     285X120
(1) Suitable material:       Pre-painted steel coil
(2) Material Thickness:      0.4 - 0.8 mm
(3) Profile width:       285 mm+/- 5mm
(4) Product Height:       120 mm+/- 2mm
(5) Profile:         Please Refer the Attached Profile Drawing.

? Production Process: 
material coil - decoiling - roll forming - hydraulic step-forming - hydraulic cutting-off - final profile (PLC controlling)

? One complete set of production line consist of following units:
1. Hydraulic  Decoiler        1 set
(1) Working Principle      Pallets Expansion by Hydraulic
(2) Max. Decoiling Width     600 mm
(3) Max. Loading Capacity     3,000 kgs
(4) Coil's Outer Diameter     1,600 mm
(5) Coil's Inner Diameter     500 - 600 mm
(6) Adjustable Speed      0 - 20 RPM
(7)  Motor        3 kw

2. Roll forming machine     1 set
(1) Rollers Station       13 Nos.
(2) Rollers' Material      45# Steel
(3) Rollers' Surface      Hard Chromed
(4) Main Shaft Diameter     60 mm
(5) Main Shaft Material      45# Steel
(6) Main Bearing       60209
(7) Plywood Thickness      22 mm
(8) AC Motor        4.0 kw
(9) Roll-Formed Speed      2 - 12 meters / minute

3. Hydraulic Cut-Off      1 set
(1) Hydraulic Pump Stand     1 set
(2) Hydraulic Pump Stand Motor   4 kw
(3) Hydraulic Pump Stand Equipment  Wind-Cooler
(4) Step-Forming Mould     1 set
(5) Cut-Off Blade       1 set
(6) Cut-Off Blade Material     Gr12 Steel
(7) Hardness Treatment     HRC 60 - 62
(8) Working Table Pressure    15 Tons

4. Simple Run-Out Table     1 Piece
(1) Structure        Panel Structure, 3 meters length
(2) Material        Welded by 50-Angle Channel Steel
(3) Quantity        1 piece

5. Electronic Control System
(1) PLC         Mitsubishi, Japan
(2) Controller        Touchable Screen
(3) Speed Adjuster       Frequency Converter, Japan
(4) Main Electronic Components   Schneider / Silin
(5) Electric Control Panel     Full-Sealed, Ventilation Cooler
(6) Control System Power     Overload Protection
(7) Electric Control Cabinet    By Aviation Connection Plugs
(8) Cut-Off Step       Machine Stopped, then Cut-Off
(9) Profile Length Control     Encoder
(10) Length Tolerance     ± 1.0 mm
(11) Power Supplier      380V, 50Hz, 3Phs

Certificates for our machines:

(1)Our engineers in the customer's workshop for INSTALLATION & TRAINING.

(2)Customers visiting our factory for machine inspection.