2016 high efficiency spray & heat powder mixer for chemical/pharmacy
JHS-P type double cones mixer is used for several small batches mixing aggregated for a big batch in order to ensure the consistency of product performance, while small amount of fluid sprayed into powder materials. Therefore large capacity, spray evenly, smooth operation, safe and convenient to use is what it requires. but the requirements for mixing standard is not too high. JHS-P type double cones mixer is produced as the above requirements.
Technical parameter
1. Mixer specification
Mixer Type | Barrel Volume(L) | Max. Loading Volume (L) | Barrel Thickness(MM) | Barrel Revolving Speed(R/M) | Blade Revolving Speed(R/M) | Motor Power (KW) |
JHS-P150 | 150 | 75 | 2.0 | 24 | 24 | 1.5 |
JHS-P300 | 300 | 150 | 2.5 | 24 | 24 | 3 |
JHS-P1000 | 1000 | 500 | 6.0 | 12 | 12 | 7.5 |
2.Metering Pump Specification
Mixer Type | Metering Pump type | Max. Flux(L/H) | Max. Pressure (Bar) | Power (KW) |
JHS-P150 | KD10 | 10 | 8 | 0.18 |
JHS-P1000 | KD30 | 30 | 8 | 0.18 |
Operating rules:
1,Machine inspecting. Install the machine, adjust the barrel, be subject to rotating flexible. Barrel is a rotating part, operator should not be close to the working machine for fear be injured.
2,Loading materials. Filling powder materials through loading port, the optimum loading rate is 45%-50%. After finish filling materials, close covering cap of loading port and adjust mixing time.
3,Settle mixing time. Mixing time can be controlled by time, it should be set up well before mixer machine working. When the machine works to the preset time, it will stop automatically( during this, press stop button ,the machine can also stop working.
4,Starting up.
A,Press button “preparation” + “operate” or “shake”, the machine starts to work. This double keying operation method is for operator’s safety, prevent personal injury caused by one keying misuse.
B, During mixer machine working, turn on the spray pump, it will spray fluid into the rotating barrel. When the fluid spray capacity meet material needs, please manually turn off power of the spray pump.
Note: This operation is independent; it is not associated with mixer machine’s working condition.
C,When the mixer machine stop working, switch on the spray pump, its working condition can be checked in real time.
5,Discharge materials. Press button “stop” to end mixing, let the discharge port rotate to the right below position by pressing “shaking” button, put a loading container at lower end of discharge port, open the valve of discharge port until all the materials discharge completely.
Fluid Injection System Operating Instructions
1. Notice
A, Before use the metering pump, please add gear lubricant to oil pointer
B, Before switch on the metering pump, make sure that the pipeline is unobstructed (valve open)
C, When the metering pump stop working, make sure that shut off the metering pump firstly, then close the fluid outlet pipe valve.
D, Outlet line pressure must be greater than the inlet line pressure.
E, Avoid metering pump pumping fluid contains solid particles.
2.Inspect working position of the fluid injection system before equipment working
A, Disconnect spray pump outlet pipe
B, Make sure that there is sufficient amount of liquid in the fluid tank.
C, Open the manual power switch of the spray pump and it begin to work independently. Observe if there is liquid outflow, if yes, it means the machine is normal. Otherwise, please detect the cause of the fault.
D, Inspect spray nozzle in the barrel clogged or not, if yes, please clean up.
3.Preparation work on the fluid spray system before mixer machine starting up
A, Adjust flow rate of fluid through manual operation rotating rod behind the liquid pump (adjust the rate between 50%-100% of the rated flow).
B, Make sure that there is sufficient amount of liquid in the fluid tank.
Zhengzhou Jin Tai Metal Materials Co., Ltd. was established in 2001.It is a mixer (also known as mixing machine) professional manufacturer. The corporation has about 125 staff, including 15 senior engineers, which integrates research and manufacture during its development. The company's production department is located in No.1 Zhongxing Road in Xinzheng city and headquartered in Weilai Garden,No 71 WeiLai Road Zhengzhou city ,which is close to the famous Zhengdong New District.
For mixing equipment, most companies are still producing the traditional equipment, some equipment didn't change over 30 years. Over the years Jin Tai cleaves to the spirits of” Made in China” in the field, devoting research to innovating in order to improve the efficiency and save more energy. At present we have the independent intellectual rights and national patent technology of our products .In the creation part of domestic mixing equipment , Jin Tai has been taking the lead.
‘Made in China’ has been the dream of several generations in industrial field. Being the main force of the independent innovation , Jin Tai has the responsibility to make a contribution to the development of Chinese industry ,and keep innovating and moving forward to make more products of high quality .
1.Some remarkable questions in the process of use.
Because the Dry Powder Mixer Machine is electrical equipment, so the operator should pay attention to electricity safety.
2.How to maintain dry mixer?
1.)Ensure that the Dry Powder Mixer Machine and the surrounding environment clean.
2.)Regular checks of the various systems, such as tainted ash, gas leakage, oil spills and leakage phenomenon timely processing.
An experienced and well mannered sales and marketing team is committed to bringing you 100% customer satisfaction. In order to succeed in the rapidly changing podwer mixer market, our company has instituted a development policy that emphasizes "Serving the customer, improving products, providing best service,sureness and steadiness, devotion and dedication".Please feel free to contact us at any time.
....