Best selling products in america q switch 1064 nd yag 532 ktp eyebrow

washing tattoo laser/laser  tattoo removal machine price

Theory:

The Q-switched ND: YAG laser delivers light of specific wavelengths with high energy which are absorbed by the pigment in the tattoo and result in a shockwave. The shockwave shatters the pigment particles, releasing them from their encapsulation and breaking them into fragments small enough for removal by the body. These tiny particles are then eliminated by the body. Since this specific wavelength can only be absorbed by pigment particles, no injury to skin and normal tissues will occur. 

Application :

The system gem-adjusting Q switch can effectively cure the mixed pigments by pigment  precipitation of the extraneous source with pathological pigment change of the endogenous source , inclusive of erroneous dark eyebrow-embroidery,lip-embroidery,lip-soak,eye line-embroidery,lip-line,tattoo (inclusive of tattoo by the extraneous wounds),pigment precipitation by sensitive source, freckle on female's face (male's),coffee spot,
old age spot,black mole,and birthmark in black, blue, purple , brown , red and etc. Treatment course for the different illness case as follows:

(1)Treatment for tattoo in eyebrow
Customer could not open eyes during treatment, operator should adjust energy according to depth of tattoo color ,hold handle and move it to treatment area slowly to make customer feel acceptable in mentally . Right now ,the speed of flash could be set 3HZ ,keep head of the handle a two-finger distance to treatment area,start treatment from head of eyebrow to  end of eyebrow .  It is needed to treat again in 5-10 minutes if the
color of tattoo re-appear.
(2)Remove eye line
The speed of flashes could be set  4-5HZ , adjust the  energy of light to minimum energy ,  keep a one-finger distance berween head of handle and treatment area . Operator should strictly protect customers` eyes  with panel for eyelid or medical pledget (panel for eyelid) of 25px depth.
Treatment should be started from down eye line,customer should deeply close eyes and keep eyeball up-sight inside .Operatoe should press

the pledget (panel for eyelid)with forefinger and push up eyelid,peel down eyelid with middle finger to bare the eye line, treat it with flashes of 4-5Hz. Then, treat up eye line.Also the customer should close eyes and keep eyeball down-sight inside .Operator should press the pledget (panel for eyelid) with middle finger and push eyelid down,push eyelid up with forefinger to bare the  eye line,  treat it  with flashes of 4-5Hz.
(3)Remove lip line
The speed of flashes could be set 5Hz,keep a 3/4 finger distance between head  of handle and  treatment area.It is better to remove black,coffee,deep, red and brown lip line with 1064nm head at first time and then, treat again with 532 nm head.
Notice: All tattoos in lip should be treated in 6  months after making .  OR removal treatment will fail.  It should have 45-60 days interval to continue next treatment until remove all.
(4)Remove tattoo
The speed of flashes could be set 3Hz/5Hz.It is better to use thehigh energy for treatment until treatment area seeps a little blood,It should have 45-90 days interval to continue next treatment until remove all.
(5)Remove spot and nevus
The speed of flashes could be set 3Hz/5Hz . Keep 3-4 fingers distance between head of handle  and  treatment area.It is better to use high energy energy for treatment until treatment area seeps a little blood .  It is advised to use 1064 nm  head for mormal spot and nevus treatment ,  but for deep deep color spot and nevus, it is better to use 532nm head for treatment. It should have a 15-30days interval to continue next treatment  until remove all.
(6)Remove birthmark
The speed of flashes could be set 3Hz/5Hz . It is better  to use high energy  for treatment until treatment area seeps a little blood,it is advised to use 1064nm head for birthmark treatment , but for the  red and deep color birthmark ,it is better to use 532nm head for treatment. it should have 45-90 days interval to continue

BD-LS (Black doll )wavelength tip: whitening ,shrinking pore , remove acne,remove blackhead.

Operation:

Laser treatment projects opetating pratices:

1064nm: regulation of energyto start with a laser gun head alignment operation portion emitting (thedistance between the gun and the skin of approximately 250px), one portionfollowed by a portion emitting until you see can be micro oozing (smear repairfactor repair).

532nm:regulation of energyto start with a laser gun head alignment operation portion emitting (thedistance between the gun and the skin of approximately 250px), one portionfollowed by a portion emitting until you see can be micro oozing (smear repairfactor repair).

BD-LS(Black doll):Cleanskin, daub medical carbon on the face (wait for 8-10 minutes).let it absorbedinto the pores. until the medical carbon become the smoke Disappear . Thenclean the face can be. Note:1064nm,532nm treatment 48 hours can not in contactwith water, the Black doll treatment 24 hours can`t in contact hot water.

Parameters:

1.Treatment head : 1064nm &532nm&Black doll

2.Laser type:  Q-switches Nd: YAG Laser

3.Energy: 0-1000mj

4.Width of pulse: 10ns

5.Frequency: 1-6 HZ

6.Spot diameter: 1-10mm

7.Cooling manner: wind water,water cooling,semi-conductor cooling system

8.Input power: AC 220V(110V)/15A 50HZ(60HZ)

Free training for operation of the machine in our company, which provided by our specialized training department.

On-line services, for example, technical consultancies provided by our skilled technique group concerning any question of the laser machine, and after-sale maintenance and more.

OEM/ODM services are available. We have our own developing and design department and manufacturing line, which ensure your required beauty machine.

Quality guarantee:One year

Our After-sales Service:

1.1 year warranty with professional support

2.Within 1 year, Supply spare parts for free if the machine has quality problem

Dear,if you have any question ,welcome to contact us !!