Pet Preform Line, buy Low Cost High Quality Two Screw 96 Cav. Pet Preform Injection Molding System on China Suppliers Mobile

Product Details

Product Information

Demark 96 cavities pet preform line molding system injection molding machine uses a new part cooling and handling system, which features:
    1. Cooling on the inner surface of the preform without using compressed air, unlike most post-mold cooling systems which only cool the outer surface
    2. Optimized cycle utilization — being mounted on the moving platen, the cooling system remains active for up to 85% of the overall cycle.

Demark pet preform injection molding systems are available from 280 to 500 tonnes (2800 to 5000 kN) and up to 96 cavities.

Demark pet injection systems offer:
    1. Faster cycles(9s)
    2. Reduced energy consumption
    3. Smaller footprint
    4. Improved repeatability
    5. Rapid set-up
    1. Two state plasticizing enables plenty injection quantity;
    2. Take out plate with three working position insures sufficient cooling time and shorter cycle time;
    3. High quality parts and accessories from world famous brands enable higher speed and precision;
    4. Special screw design increases torque while brings down shear force to avoid degradation;
    5. Accumulator from world reputable manufacture increases performance while brings down power consumption;

Reflex Platens
Reflex platens distribute clamp force evenly across the platen face.
Reflex platens:
    1. Allow for 10-30% lower clamp tonnage
    2. Decrease mold wear
    3. Improve part quality

Injection Units
demark systems offer both reciprocating screw (RS) and two-stage injection units. RS units offer the performance required for many PET applications while two-stage is appropriate for higher throughput applications.

Controls
DMK-based controls manage all functions of our PET production systems, with optional packages to integrate auxiliaries and downstream part handling equipment. Advantages include:
    1. Faster cycle times
    2. Improved shot-to-shot repeatability
    3. Remote connectivity through ServiceNetLink
    4. Control of molding system and auxiliaries from a single interface

Linear Bearings
Linear bearings support the moving platen directly on the machine base. This design reduces mold wear by improving platen alignment and perpendicularity, and provides a grease free molding environment.

Features:

ITEM		UNIT	DMK-PET96
INJECTION UNIT	Screw L/D Ratio	L/D	25
	Screw Diameter	mm	140
	Injection Pressure	Kgf/cm²	907
	Output(Max)	Pcs/h	30000
	Theory Shot Volume(Max)	cm	5400
	Shot Weight(PS)	g	6510
	Shot Weight(PS)	ozs	230
CLAMPING UNIT	Clamping Force	T	600
	Clamping Stroke	mm	730
	Max/Min Thickness of Mould	mm	450~870
	Space Between Tie Bars (WxH)	mm	920~1220
	Ejector Stroke	mm	200
	Ejector Force	T	21
	NO.of Ejector Pins	PCS	13
	Max Pressure of System	Kg/cm²	140
MOULD&ROBOT	Cavity(Max)	PCS	96
	Neck of Bottle(Max)	mm	42
	Length of Preform(Max)	mm	220
	Weight of Preform(Max)	g	35
	Type of Mould	Needle Valve of No-Cutting PET Preform Molds
	Manipulator	Cavity	96x3
	Cooling Form	Cavity	288
POWER UNIT	Pump Motor Power	KW	42
	Robot Power	KW	42
	Mould Heater Capacity	KW	72
	Heater Input Capacity	KW	125
	Total Power	KW	424
OTHER	Electric Power Supply(3-phase AC)	V/HZ	380/50
	Chilling Water	°C	5~15
		Mpa	0.6
		L/min	1200
	Coolling Water	°C	30~55
		Mpa	0.25
		L/min	400
	Compressed Air	Mpa	0.7~0.9
	Compressed Air	L/min	1500
	Machine Size (LxWxH)	mm	11060x4847x2450

Company Profile

Certifications

Exhibition Display