xDSL, buy Sino-Telecom 8-port ADSL Repeater / Loop Extender AER800-8PL on China Suppliers Mobile

Product Details

Product Description

Overview

The ADSL Loop Extender expands the coverage of ADSL lines. It will provide systems with a higher performance-to-cost ratio, improve equipment utilization rates, and optimize the network. This product will allow you to double the distance between CO and CPE.

The ADSL Loop Extender is an active element installed in the outside loop plant. It operates as an amplifier and equalizes the signal.

The line powered ADSL Loop Extenders consist of an enclosure and card system designed to offer a modular deployment option. The parts list is detailed below:

AER800-1PL: Stand-alone 1 port unit.
AER800-4PL Box: A Box for up to 5 AER800-C1PL cards.
AER800-8PL Box: A Box for up to 9 AER800-C1PL cards.
AER800-C1PL: A one port ADSL Loop Extender designed to be inserted into the backplane of any AER800-PL enclosure.

NOTE: Product is suitable for ADSL2/ADSL2+ over POTS subscriber.

Benefits

Extend ADSL coverage.
Boost ADSL rates.
No power supply required.
No need to install any equipment in the CO.
Low power consumption; uses the -48V on the line from PBX.
Additional subscribers can be added by inserting additional AER800-C1PL cards into the enclosure.
IP-66 Rated enclosures.
Over-current protection to protect from lightening.
Easy to install, deploy, and maintain.

Technical Specifications

Technical Specifications of AER800-1PL Box, AER800-4PL Box, AER800-8PL Box, and the AER800-C1PL card:

Operating Environment	Temperature	-35℃~+65℃
Operating Environment	Relative Humidity	5%~95% (Non-condensing)
Input Power	DC36V~DC72V
Power Consumption	Less than 0.1W( per port )
Lightning-proof grade	4000V(10/700μS)
Number of supported subscribers	AER800-1PL	1 ADSL subscriber
	AER800-4PL	5 ADSL subscribers
	AER800-8PL	9 ADSL subscribers
Dimension(LWH)	AER800-1PL Box	160mm×70mm×48mm
	AER800-4PL Box	215mm×290mm×82mm
	AER800-8PL Box	315mm×290mm×82mm

Application

Application

1. Equipment connection diagram:

ADSL Loop Extender Application Diagram

L1: The signal-twist pair connecting ADSL Loop Extender to DSLAM.

L2: The signal-twist pair connecting ADSL Loop Extender to Modem.

2. Resistance and distance demand

The recommended installation conditions are as follows:

(1)24 AWG(0.5mm) twist pair

The Demand about Resistance and Distance of 24AWG:

Route	Loop Resistance Demand Ohms	Distance Demand
Route	Loop Resistance Demand Ohms	Kfeet	Km
L1(CO-Extender)	480 ~ 1032	9.2 ~ 19.7	2.8 ~ 6.0
L2(Extender-CPE)	86~ 929	1.6 ~ 17.7	0.5 ~ 5.4
L(CO-Extender-CPE)	568 ~ 1445	10.8 ~ 27.6	3.3 ~ 8.4

(2)26 AWG(0.4mm) twist pair

The Demand about Resistance and Distance of 26AWG:

Route	Loop Resistance Demand Ohms	Distance Demand
Route	Loop Resistance Demand Ohms	Kfeet	Km
L1(CO-Extender)	635~ 1250	7.5 ~ 14.8	2.3 ~ 4.5
L2(Extender-CPE)	88~ 1184	1.0 ~ 13.2	0.3~ 4.0
L(CO-Extender-CPE)	715~ 1650	9.3 ~ 21.7	2.8 ~ 6.5

Note: The switches on the PCB are default setting on “LOW” when ex-work.

Physical Structure

Physical Structure

AER800-1PL: Stand-alone 1 port unit.
AER800-4PL Box: A Box for up to 5 AER800-C1PL cards.
AER800-8PL Box: A Box for up to 9 AER800-C1PL cards.
AER800-C1PL: A one port ADSL Loop Extender designed to be inserted into the backplane of any AER800-PL enclosure

1. AER800-1PL Box

AER800-1PL Box

Twist-pair Connection Description of AER800-1PL

Color	Connection
Orange/White (A/B)	to DSLAM
Green/White (A/B)	to Modem
Blue/White (A/B)
Brown/White (A/B)

2. AER800-4PL Box

AER800-4PL Box

The AER800-C1PL modular card system allows for plug and play installation of new subscribers. Wiring terminals on the backplane connect to the existing copper loop plant.

3. AER800-8PL Box

AER800-8PL Box

The backplane of the AER800-PL series enclosures contain wiring terminals for connecting the extender to the existing loop plant. “CO” connects the signal line from the DSLAM to AER800-C1PL; “CPE” connects the line to the customer modem

4. AER800-C1PL Subscriber Card

LED lights indicate power status. Additionally, the AER800-C1PL cards contain DIP switches designed to operate with different CO telephone switches, please follow the following picture:

As you can see, the switches are default setting on “LOW” when ex-work, which requires that the distance L1 from CO to the ADSL loop extender must be longer than 2.8km on 24AWG or longer than 2.3km on 26AWG. At this time, the ADSL loop extender’s working current is 4.2mA.

In case that L1 couldn’t be longer than 2.8km on 24AWG or couldn’t longer than 2.3km on 26AWG, you can set the switched to “HIGH”. At this time, the ADSL loop extender’s working current is 6.2mA, and two things are needed to be noted:

1. L1 must be longer than 2.4km on 24AWG or longer than 2.0km on 26AWG;

2. The threshold of telephone switch is higher than 6.2mA.

Installation

Installation Procedure

1. Unpack

When unpacking the equipment, be sure to check the contents of the packaging for completeness against your purchase order. Notify your supplier immediately if any items are missing.

Note: Please save packing material. All equipment returned must be packed in the original packing material.

Be sure to inspect the equipment for shipping damage, including bent or loose hardware, and broken connectors. If the equipment appears to have been damaged in transit, please contact your supplier.

2. ADSL Loop Extender Installation

(1) The AER800-1/4/8PL Box can be installed in a junction cabinet, pedestal, or pole mounted via the supplied mounting brackets. Once mounted, ground the unit via the supplied grounding screw on the bottom outside of the box.

Attention: Copper-core wire with no less than 2.5mm2 (13 AWG) diameter is required as ground wire. One end of the wire should connect to Loop Extender’s ground terminal. The other end of the wire should connect to a good grounding point. Grounding reliability is the best way to protect the unit against lightning damage.

(2) Insert the AER800-C1PL card into the AER800-4/8PL Box.

(3) Connect the line from the DSLAM to the “CO” terminal, and connect the line linked to the customer’s modem to the “CPE” terminal. Once the “CO” pair is connected, the power LED will come on to indicated the AER800-C1PL card is operational.

(4) After confirming that all the twist-pair cables are connected correctly, and the AER800-4/8PL is securely installed, the extender will function 10 seconds after power is steadily applied.

Attention:

“A” and “B” represent tip and ring of the twisted-pair. No polarity.

Troubleshooting

Troubleshooting

ADSL Loop Extender Troubleshooting

Problem Description		Possible Reason	Suggested Resolution
Equipment does not work after connected. Status LED is OFF.		CO side cable is not connected properly.	Check CO side cable.
No Sync.	AER800-C1PL status LED is on.	Cables at DSLAM or Modem side are connected on wrong side.	Correct the cable connection.
		Line quality issues.	Diagnose cable for proper Ohms/Attenuation values.
		There is a telephone before the splitter on CPE side.	Discard the telephone before the splitter on CPE side.
		ADSL Loop Extender is not connected properly.	Correct the cable connection, or check whether the distance between the DSLAM, Extender, and Modem is within recommended values.
		L1 or L2 is too short.	Check that loop extender placement meets engineering requirements.
		SNR Margin is too high.	Reduce SNR Margin setting on the DSLAM until a connection is made. We suggest using SNR Margin < 10. Testing with SNR margin = 1 can provide useful hints during troubleshooting.
There is noise on the user’s telephone line.		CO/CPE cable is connected to ground or the wire insulation is faulty.	Check the cables.
There is noise on the user’s telephone line.		Possible electromagnetic interference.	Check to ensure the extender is not located near any high voltage equipment.
Internet is slow, frequent disconnects.		Possible PC issues, virus, hardware malfunction, etc.	Verify issue with test set or a known good piece of hardware. Check statistics on modem and DSLAM.
		Parallel open wire at CPE is too long or the connector is rusted.	Change the parallel cable to copper twisted-pair.
		The CPE side cable has too many connectors.	Avoid exposed connectors, use good quality cable.
		SNR Margin too low.	Increase the SNR margin setting in the DSLAM to 6 or more.
		Bit Error Rate too High.	Increase SNR Margin setting in the DSLAM.
		Data profile is too high for this circuit.	Lower the minimum data rate in the DSLAM.

Product Category

Product Category

1. WDM Optical Transport System 2. Optical Line Protection Switch

3. xDSL 4. GPON/EPON

5. Lawful Interception 6. Network Interface Card

7. TAP 8. Wireless AP

FAQ

FAQ

1. What are your terms of payment?

Usually, we can accept T/T, PayPal and Western Union. You can select the terms of payment which is more convenient for you.

2. What about the lead time?

Usually, if there is stock of goods, we will deliver the goods within 3~5 work days after we receive the payment.

3. How about the shipping?

Usually, we will deliver the goods via International Express like FedEx, DHL, TNT, and UPS and so on. Door to door delivery service will be provided.

4. How can I place an order?

(1) Agreement is achieved on the product price and product specifications.

(2) We make proforma invoice for your confirmation.

(3) When you agree on the proforma invoice, you make the payment.

(4) We deliver the goods after we receive your payment.

5. Can you do OEM for us?

Yes. If there is a certain order quantity, we can do OEM including printing, logo, and customized model for you.

6. What are the advantages of your products?

A. Good quality and competitive prices.

B. Strict quality control during production process.

C. Professional operations in processes of production, sales, assembling, packaging and shipping.

D. Good after-sale service. Professional online technical support can be provided. Moreover, if there is any problem of the goods, we will help to solve the problem or provide replacement of the goods.