• CS9933N AC dielectric strength(also called AC hipot tester, AC withstanding voltage tester) DC hipot tester/IR(insulation resistance) /Ground resistance four function in one tester
• The standard preventive safety system(with OK light, over zero start,The high voltage indicator, high voltage indicate column)
• Fast voltage rise time(within 100ms) 
• Automatic measurement stability control system
• Test the load with different characteristic, resistance, capacitance and inductance
• Discharge within 0.2 seconds 
• Set voltage rise time, test time and interval timeWith arc detection, set arc detection level(set ARC senstivity)
• Five memory group, five test steps
• Both cycle test and single step test are supported by the multi-step test, which is applied to the test of different parts for different requirements
• Record the start and reset times, with statistics function.
• 50Hz,60 Hz optional frequency
• Standard PLC interface, optional remote test probe and U disk storage.

Model

CS9933N

CS9933AN

CS9933DN

ACW

Output

voltage

range

0.200kV~5.000kV

accuracy

±(2%read+5V)

resolution

1V

Max output power

100VA(5.000kV/20mA)

Max test current

20mA

Low-current

0~20mA,0= not judged

Range

2mA,20mA

Output Waveform

Sine wave

Waveform Distortion

≤2%( Unloaded or pure resistance of the load)

Crest factor

1.3~1.5

Waveform mode

DDS+ Amplifier

Rise time

0.3s~999.9s  0= OFF

Test time

0.3s~999.9s  0=continuous

Interval time

0.0s~999.9s  0= OFF

ARC detection

0~9,0= OFF

DCW

Output

voltage

range

0.200kV~6.000kV

accuracy

±(2%read+5V)

resolution

1V

Max output power

60W(6.000kV/10mA)

Max test current

10mA

range

2mA,10mA

Ripple coefficient

≤5%

Discharge time

≤200ms

Maximum charge current

10mA

Voltage rise time

0.3~999.9s  0=OFF

Test time

0.3~999.9s  0=continuous

Interval time

0.0~999.9s  0=OFF

ARC

0~9,0=OFF

IR

Output

voltage

range

0.05kV~1.00kV

accuracy

±(2%read+5V)

resolution

10V

Maximum upper limit

10.00GΩ

Maximum lower limit

10.00GΩ

Minimum lower limit

1MΩ

Voltage rise time

0.3s~999.9s  0=OFF

Test time

0.3s~999.9s  0=continuous

Interval time

0.0s~999.9s  0=OFF

Discharge time

≤200ms

GR

Output Current

range

(5.0~32.0)A

(5.0-25.0)A

(3.0~10.0)A

accuracy

±(2%read+2counts)

resolution

0.1A

Max. output power

153.6VA

93.75VA

60VA

Upper limit set

600m

Output waveform

Sine waveform

Waveform distortion

≤2%( Unloaded or pure resistance of the load)

Crest factor

1.3~1.5

Signal type

DDS+ Amplifier

Test time

0.3s~999.9s  0=continuous

Interval time

0.0s~999.9s  0=OFF

Resistance offset

0~10mΩ

Volt meter

Range

0.050kV~6.000kV

Accuracy

±(2%read+5V)

Resolution

1V

Displayed value

RMS

AMPERE

METER

(H.V.)

Range

AC

0 ~ 20.00mA

DC

0 ~ 10.00mA 

Resolution

AC

2mA:1uA, 20mA:10uA    

DC

2mA:1uA, 10mA:10uA

Accuracy

±(2%+5counts)

OHM METER

(I.R.)

Range

1MΩ~10.00GΩ

Resolution

1MΩ~9.99MΩ:0.01MΩ,10MΩ~99.9MΩ:0.1MΩ,

100MΩ~999MΩ:1MΩ,1.00GΩ~10.00GΩ:10MΩ

Accuracy

0.25kV:1MΩ~999MΩ   ±5%,1.00GΩ~3000MΩ  ±10%

0.50kV:1MΩ~999MΩ   ±5%,1.00GΩ~10000MΩ  ±10%

1.00kV:1MΩ~999MΩ   ±5%,1.00GΩ~10000MΩ  ±7%

AMPERE

METER

(G.R.)

Range

(5.0~32.0)A

(5.0-25.0)A

(3.0~10.0)A

Resolution

0.1A

Accuracy

±(2%+2counts)

Display

RMS

OHM METER

(G.R.)

Range

0~510mΩ

0~600mΩ

Accuracy

±(2%+2mΩ)

Resolution

1mΩ

Measurement

Four terminal method

TIMER

Range

0~999.9s

Resolution

0.1s

Accuracy

±(1%+50ms)

Memory group

20

Test step

8