• CS9922N AC dielectric strength(also called AC hipot tester, AC withstanding voltage tester) DC hipot tester/IR(insulation resistance) three function in one tester
• The standard preventive safety system(with OK light, over zero start,The high voltage indicator, high voltage indicate column)
• Fast voltage rise time(within 100ms) 
• Automatic measurement stability control system
• Test the load with different characteristic, resistance, capacitance and inductance
• Discharge within 0.2 seconds 
• Set voltage rise time, test time and interval timeWith arc detection, set arc detection level(set ARC senstivity)
• 20 memory groups, 8 test steps in each group
• Both cycle test and single step test are supported by the multi-step test, which is applied to the test of different parts for different requirements
• Record the start and reset times, with statistics function.
• 50Hz,60 Hz optional frequency
• Standard PLC interface, optional remote test probe and U disk storage.

Model

CS9922N

CS9922AN

ACW

AC high voltage

Output

voltage

range

0.200kV~5.000kV

accuracy

±(2%read+5V)

resolution

1V

Maximum power

60VA(5.000kV/12mA)

Maximum test current

12mA

Low-current

0~12mA,0=OFF

Current Range

2mA,12mA

Waveform

Sine waveform

Distortion

≤2%( Unloaded or pure resistance of the load)

Crest factor

1.3~1.5

Waveform mode

DDS+ Amplifier

Rise time

0.3s~999.9s  0=OFF

Test time

0.3s~999.9s  0=Continuous test

Interval time

0.0s~999.9s  0=OFF

ARC detection

0~9,0=OFF

DCW

 DC high voltage

Output

voltage

range

0.200kV~6.000kV

--------

accuracy

±(2%read +5V)

--------

resolution

1V

--------

Maximum power

30W(6.000kV/5mA)

--------

Maximum test current

5mA

--------

Current Range

2mA,5mA

--------

Ripple coefficient

≤5%

--------

Discharge time

≤200ms

--------

Maximum charge current

5mA

--------

Voltage rise time

0.3~999.9s  0=OFF

--------

Test time

0.3~999.9s  0=continuous test

--------

Interval time

0.0~999.9s  0=OFF

--------

ARC detection

0~9,0=OFF

--------

IR

 insulation resistance test

Output voltage

range

0.05kV~1.00kV  10V each step

accuracy

±(2%read+5V)

resolution

1V

Upper limit set(max.)

10.00GΩ

Lower limit set(max.)

10.00GΩ

Lower limit set(min.)

1MΩ

Voltage rise time

0.3s~999.9s  0=OFF

Test time

0.3s~999.9s  0=Continuous test

Interval time

0.0s~999.9s  0==OFF

Discharge time

≤200ms

 Volt

meter

range

0.050kV~6.000kV

0.050KV~5.000kV

Accuracy

±(2%read+5V)

Resolution

1V

Displayed value

RMS

Ampere

meter

range

AC

0 ~12.00mA

0 ~12.00mA

DC

0 ~ 10.00mA

-----------

resolution

AC

2mA:1uA,   20mA:10uA

DC

2mA:1uA,

10mA:10uA

-----------

Accuracy

±(2%+5counts)

ohm meter

Range

1MΩ~10.00GΩ

Resolution

1MΩ~9.99MΩ:0.01MΩ,10MΩ~99.9MΩ:0.1MΩ,

100MΩ~999MΩ:1MΩ,1.00GΩ~10.00GΩ:10MΩ

Accuracy

Voltage ≤0.25kV:1MΩ~999MΩ   ±5%,1.00GΩ~3000MΩ  ±10%

Voltage ≤0.50kV:1MΩ~999MΩ   ±5%,1.00GΩ~10000MΩ  ±10%

Voltage ≤1.00kV:1MΩ~999MΩ   ±5%,1.00GΩ~10000MΩ  ±7%

Timer

Range

0~999.9s

Resolution

0.1s

Accuracy

±(1%+50ms)

Memory group

20

Test step

8