CTOPERATED DIN RAIL THREE PHASE LCD DISPLAY ELECTRONIC ENERGY METER WITH FAR INFRARED AND RS485 COMMUNICATION
USD $45.26 - $46 /Piece
Min.Order:1 Piece
Yueqing Yomin Electric Co., Ltd.
THREE PHASE DIN RAIL ACTIVE ANALOG ENERGY METER WITH PULSE OUTPUT
LCD DISPLAY SINGLE PHASE MULTI-RATE ENERGY METER WITH FAR INFRARED AND RS485 COMMUNICATION
100A Single Phase Square Electric Meter Socket/Meter Base with Hub
127V 230V 5(30)A single phase din rail active energy meter with analog display
200A Single Phase/ Three Phase Square Meter Socket/Meter Base ( 4 jaws, 5 jaws, 7 jaws/4J, 5J, 7J )
Model YEM021AC three phase four wire electronic DIN rail active energy meter is a kind of new style three
phase four wire active energy meter, it adopts micro-electronics technique, and imported large scale integrate
circuit, uses advanced technique of digital and SMT techniques, etc. The meter completely accords with relevant
technical requirements of class 1 three phase active energy meter stipulated in international standard IEC 62053-21.It can accurately and directly measure 50Hz or 60Hz active energy consumption from three phase four wire AC
electricity net. This meter has seven digits LCD displays shows the active energy consumption. And there are
far infrared and RS485 communication module in it. Contact with all kind of AMR system conveniently It has
following features: good reliability, small volume, light weight, specious nice appearance, convenient installation, etc.
1.35mm standard DIN rail installation , complying with standard DIN EN50022. Or front board installed
(mounting holes center distance 63 mm), users can choose any one by themselves.
2.Ten pole width (Modulus 12.5mm), complying with standard JB/T7121-1993.
3.Type S wiring (Inlet from bottom, outlet from top), use CT connect operation, may select set 27 ratio, after
set the meter will direct reading when read, and haven’t multiplied by rate of CT.
4.Seven digits display LCD, 5+2 digits display (99999.91 kWh, only ratio of CT when 5:5 A) or 7digits, it is
choose by ratio of CT which is set.
5.There are a polarity port of pulse output passive closed and a nonpolarity port of pulse output passive
distant (the output rate is 10 kWh/pulse), ). Complying with standard IEC 62053-31 and DIN 43864.
6.Standard configuration there are a port of far infrared data communication and a port of RS485 data
communication. Communication agreement complying with standard DL/T645-1997, can also choose
without function of data communication. (Product Configuration code is NC).
7 .ix LED instructions respectively every power supply state, signal of closed energy impulse and distant
energy impulse and data communication state.
8.Automatic detection the direction of the flow of load current. And Instructions on individual LCD
9.Single direction three components measure three phase four wire active energy consumption. It is
nothing with direction of the flow of load current. Complying with standard IEC 62053-21.
10.Standard configuration short terminals cover, may select extension terminals cover, in order to protect
to use safety. (Product Configuration code is AF).
Model | Accuracy | Reference Voltage(V) | Current specifications(A) | Starting current(A) | Insulation performance | ||
YEM021AC | Class 1 | 3×127/220 3×230/400 | CT/5A | 0.01 | AC voltage 4kv for 1 minute, 1.2/50us waveform impulse voltage 6kv |
Terminal | Note | Terminal | Note | ||
L1 | L1 phase CT | 9 | L1 phase line | ||
L2 | L2 phase CT | 11 | L2 phase line | ||
L3 | L3 phase CT | 13 | L3 phase line | ||
(Inlet from bottom, outlet from top) | N | Neutral line | |||
7 and 8 | Port of pulse output passive closed | 5 and 6 | Port of RS485 data communication | ||
3 and 4 | Port of pulse output passive distant | 1 and 2 | Port of CT ratio which is set |
CT DIN RAIL THREE PHASE LCD DISPLAY ELECTRONIC ENERGY METER WITH FAR INFRARED AND RS485 COMMUNICATION