High quality of grille machine/bar screen
USD $3,200 - $26,000 /Set
Min.Order:1 Set
Qingdao Yimei Environment Project Co., Ltd.
High quality of grille machine
Water supply and drainage engineering pump stations, water inlet fine grille, remove fine grille between the grid slag;
Textile, printing, dyeing, slaughtering, leather papermaking industrial wastewater solid-liquid separation;
Sugar, wine, food processing of solid-liquid separation.
2. Working principle:
This grille machine consists of ABS engineering plastic, nylon or stainless steel special shape, press the certain harrow tooth gear assembly rankings formed on the shaft gear chain, the closed-end rake in the lower installation in water into the canal. When driving system drive sprockets more uniformly and directional spin, the whole rake tooth chain and top-down movement, and bring a solid material from liquid isolated, fluid, through the rake the tooth of the gate, the whole working flow past band continuous state. Due to the special structure harrow tooth shape, make rake tooth chain carries sundry reach top retrorse motion before, back when the relative harrow tooth clear between campaign to get off, and sundry rely on gravity behind a pair of glue set equipment to ensure each row BanShua harrow tooth movement to this position can be thoroughly clean the brush role.
3. Product features:
This grille machine is the biggest advantage is a high degree of automation, high separation efficiency, power consumption is small, no noise, corrosion resistance, good performance in unmanned circumstance can ensure continuous stable work, set up overload safety protection devices, in equipment is at fault, will produce the acousto-optic alarm and automatic stop, can avoid equipment overload.
This equipment can according to user needs to arbitrarily regulate equipment operation, running, realize periodic intervals According to level difference before automatic control of geogrid; And a manual control functions, with convenient maintenance. Users can use either the work according to different selection
Because this equipment structural design is reasonable, in equipment, his own strong self-purification, won't produce jam phenomenon, so few daily maintenance workload.
Equipment specification according to machine YMGS300-1500 width points type. Machine, then make it more than 1500mm wide and online. Bar gap 1mm, 3mm, 5mm into 10mm, 20mm, 30mm, 40mm, 50, from various specifications, water, hoisting height had total, solid-liquid separation and the shape of separation material, particle size to choose bar gap. Can be based on user needs to choose material of ABS engineering plastic, nylon, stainless steel production; the rake tooth Main frame has stainless steel material and carbon steel corrosion two kinds.
4. Installation and debugging instructions
1). grille decontamination machine in hookon before installation should check the embedded steel location, size if it meets requirements, should guarantee;
A, grille Wells with two side should be vertical plane, well grille its perpendicularity tolerance weight may not exceed 20mm.
B, grille Wells should be parallel, both sides does not exceed the parallelism 20mm.
C, belt anchor foot two embedded steel plate should be and grille Wells plane surface flat top platform.
2). as the machine without making the depth, grille provide ditch decontamination machine into the groove, calibration Angle, the grille bearings after, based on the floor on side and grille ready, its frame welding installation Angle must comply with the design requirements, ensure the installation of an envisagement gear rake spent less
than 1/1000mm, then tighten the anchor nut (if no embedded steel plate, usable expansion bolt).
3). discharge area safety cover, relax when tight sprocket, remove reducer end chain, electricity commissioning, see whether the steering gear reducer with safety cover as shown on the shoulder is consistent, forbidden to reverse direction.
4). use tensioner sprocket, adjust the chain firmness with tensioner screw adjusting rake the tooth chain firmness.
5). check reducer lube oil noodles line, whether to insufficient JiXieYou added to with size 46 oil noodles line. (equipment first operation shall first charging 46 # oil to decelerate oil a line)
(the machine has added oil, replaced once a year)
6). pack on safety cover, the switch on the power no-load running, there shall be no jitter, jam and abnormal noise, no-load experiment, then input load operation operation.
5 .Common breakdown and elimination method:
1) in normal operation appears in motor running gear surface not running rake.
Fault reason: overloading and cause overload safety pin was cut off.
Elimination method:
(1) will be replace overload safety cover safety pin;
(2) found out by overloading reason, main look to whether sundry stuck rake chain;
(3) if there is sundry stuck rake chain, remove sundry rear can boot;
(4) rake in the chain chain attrib wattle wear with, must be replaced chain plank.
Replacing steps:
(1) the two root with iron stick will rake tooth chain stuck.
(2) use card spring clamps will have to replace chain chain of batten harrow tooth kadar discharge reed.
(3) will be two root rake tooth pulled pin shaft chain to replace new chain, then put the pin shaft strips in turn the card inserted, reed mount.
(4) installed hole plate can overhaul.
Three, routine maintenance and maintenance
(1) in the operation process, such as fibre beneficent bars around in sundry etc, should be clear in time, lest affect the normal operation of the machine.
(2) in normal operation, machine every two months, must use butter gun in all lubricating parts of the nozzle calcium grease Once injection