Product Details

Specifications

powerline adapter
1. 130Mhz mcu,448k RAM,512K ROM
2. extendable ROM
3. 150Mbps 2.4g WIFI uart.
4. low power

powerline adapter

The Oolite_o1 is a low-power Wi-Fi connectivity module for the Internet of Everything. internal Alljoyn protocol.
The module support IEEE 802.11b/g/n protocol. The module includes a number of TCP/IP-based
connectivity protocols along with SSL,enabling a low-cost,low-complexity system to obtain
full-featured internet connectivity and reliable information exchange.
The module is based on QualcommAtheros QCA4004 which is highly integrated, and
includes an energy efficient on-board power amplifier and LNA.
The module provide two interfaces for connecting to local system controller. A UART-based
host interface can be used for rapid development and deployment of simple data streams between
the local device and the internet cloud. An SPI slave interface is available for applications that
require more advanced connectivity to the network.

CHIPSET QCA4004 has a 130Mhz xtensa CPU, 448K ram and 512K rom(extendable )

IEEE802.11b/g/n (1x1) based on QualcommAtheros QCA4004 solution
Support UART Interface
Support SPI slave interface
Support I2S slave interface
Support I2C master interface
Module is powered by the host with a 3.3V +/- 10% supply.
One U.FL antenna connector inside the module
4 layers through hole PCB design with high Tg (170 degrees) FR4 material

Interface
14pin connector or Half Hole
Antenna: IPEX connector or Chip Antenna

Pinout.

Number Symbol Name Status Pin Description

1 USB_DP I/O USB signal D+

2 USB_DN I/O USB signal D-

3 WAKE_UP I Wakeup Control.While in SUSPEND state,the QCA4004 monitors

this pin,and if a falling edge or rising edge is detected,the resume

from SUSPEND sequence is started.(Default)

CHIP_PWD_L I Chip power-down control

4 SPI_CLK I SPI slave CLK

5 GND P Ground pad

6 SPI_MISO O SPI slave output

7 I2C_SCK O I2C master SCK

8 SPI_MOSI I SPI slave input

9 I2C_SDA I/O I2C master SDA

10 SPI_CS I SPI slave CS

11 UART_RXD I UART RX

12 GND P Ground pad

13 UART_TXD O UART TX

14 VCC P 3.3V power supplies

Bootstarp Pin

SPI_CS Hostmode 0 Rerserved

                                        1           The module bootup is under control of host
                                                     CPU via SPI slave interface.The external
                                                     CPU is required and the SPI interface is the
                                                     host interface.

                                                     Internal pull-up with 10kohm resistance.
                                                     If you want to use the SPI interface,pls ensure this pin is high when
                                                     power-up. Otherwise let it floating

Environment Storage Condition

Temperature
Operating Temperature: -10 deg.C ~70 deg.C
Storage Temperature: -40 deg.C ~80 deg.C
Humidity
Operating Humidity: 5% ~95% (Non-condensing)
Storage Humidity: 5% ~95% (Non-condensing)

RF Specification

Parameter Min. Typ. Max. Unit
Rx input frequency range 2.412 - 2.484 GHz
TX Characteristics Min. Typ. Max. Unit
1. Power Levels
1)Target Power@1Mbps 15 17 19 dBm
2)Target Power@11Mbps 14 16 18 dBm
3)Target Power@6Mbps 14 16 18 dBm
4)Target Power@54Mbps 12 14 16 dBm
5)Target Power@HT20-MCS0 13 15 17 dBm
6)Target Power@HT20-MCS7 11 13 15 dBm
7)Target Power@HT40-MCS0 12 14 16 dBm
8)Target Power@HT40-MCS7 10 12 14 dBm
2. Frequence Error - ppm
3. Modulation Accuracy(EVM)@Target Power
1) 54Mbps - -30 -25 dB
2) HT20-MCS7 - -32 -28 dB
3) HT40-MCS7 - -33 -28 dB