XKPLC-FX2N PLC trainer composed by PLC core board, DC24V power source, button (three with lock, three without lock), eight of LED indicator, traffic light simulation unit etc. PLC core board with 12-way on/off input, 8 -way relay output. Directly using Mitsubishi GX Developer software for programming, support on-line monitoring, serial port download directly, conveniently development. Trainer finish the PLC program software learning, programming instruction learning and application training, PLC typical programming method learning, PLC typical project training etc.

(1) Source voltage: single phase AC220V, 50Hz

(2) Referring size: 370*220*120mm

(3) PLC core board

   1) working voltage: DC24V

   2) with 12 point digital quantity input, 8 point relay type digital quantity

output

3) directly using Mitsubishi GX Developer software for programming

4) support on-line monitoring, serial port directly download

5) maximum memory capacity: 8000 steps

6) Inner source

   Soft components:

X0-X32,Y0-Y32,

   M0-M255,M512-M768(power off and holding),

   S0-S255,

   T0-T23(100mS timer),T200-T215(10mS timer),T250-T255(100mS cumulative timer),

   C0-C31,C200-C203 (32 bit add-subtract power off and holding counter), C235 (32 bit high-speed add-subtract power off and holding counter),

   D0-D80,D512-D527(power off and holding)

   V0-V7,Z0-Z7.

Special soft components:

   M8000(operation monitoring contact), M8001(operation monitoring contra-contact).

   M8002(Initial pulse contact),M8003(Initial pulse contra-contact).

   M8004(error indication contact).

   M8011(10 ms clock pulse),M8012(100 ms clock pulse),M8013(1s clock pulse),M8014(1 min clock pulse).

   M8020(zero position flag),M8021(borrow flag),M8022(carry flag).

   M8029(instruction execution ending flag).

   M8033(memory holding contact).

   M8034 (output disable contact).

   M8200-M8203(C200-C203 count direction).

   M8235(C235 count direction).

   D8000(monitoring timer set point).

   D8012(Max. scanning time).

   D8140(Y0 pulse output counting register)

Support constant:

K range: -32768-32767 or 0-65535; H range: 0-FFFFH.

At present, not support 32 bit operation

7) Supported commands set

Basic instruction:

LD,LDI,AND,ANI,OR,ORI,INV,OUT(OUTT,OUTC),SET,RST,ANB,ORB,LDP,LDF,ANDP,ANDF,ORP,ORF,PLS,PLF,MPS,MRD,MPP,RET,NOP,END.

Contacts compare instruction:

LD>=,LD<=,LD>,LD<,LD<>,LD=,AND>=,AND<=,AND>,AND<,AND<>,AND=,OR>=,OR<=,OR>,

OR<,OR<>,OR=.

Transfer and compare instruction:

   MOV,CML,XCH,BCD,BIN,CMP,ZCP,FMOV.

Arithmetic instruction:

ADD,SUB,MUL,DIV,INC,DEC,WAND,WOR,WXOR,NEG.

Cyclic shift instruction:

ROR,ROL,RCR,RCL.

Data processing instruction:

   ZRST,DECO,ENCO,SUM,BON,MEAN.

Program flow instruction:

CJ(Max. 16 addresses), CALL (Max. level 5 nesting, 16 sequences), SRET, FEND, WDT, FOR(Max. level 5 nesting), NEXT.

(1) Power line       1pc

(2) 2mm jumpers    30pcs

(3) PLC programming cable 1pc

(4) programming software: GX Developer

(1) Programming software learning

   New set up PLC program, ladder diagram or STL program, program download, program on-line monitoring

(2)PLC instruction training

(1) Basic logic instruction learning and training

(2) Extension logic instruction learning and training (setting and reset coil, invert, rising edge, falling edge)

(3) Timer instruction learning and training

(4) Counter instruction learning and training

(5) Transfer instructions learning and training

(6) Compare instruction learning and training

(7) Logic instruction learning and training

(8) Operation instruction learning and training

(9) Data shift instruction learning and training

(3)Ladder diagram basic circuit training

(1) Start, self-keep, stop circuit

(2) Start, self-keep, stop circuit of multipoint control

(3) Interlock control circuit

(4) Cycle flashing circuit

(5) Timer relay circuit

(6) Time delay connect, time delay disconnect circuit

(7) Maintain signal to pulse signal circuit

(8) Get through time delay to off time delay circuit

(4)PLC typical training item

(1) Motor start and stop control experiment

(2) Motor forward and reversal running control experiment

(3) Motor Y/Δ startup control experiment

(4) 2 motors sequence start-up, same time stop control experiment

(5) 2 motors sequence start, sequence stop experiment

(6) Traffic light control experiment

                     Ms. Sally Zhao

                     Skype: xksally

                     Tel: +86-531-88771298

                      Shandong Xingke Intelligent Technology Co., Ltd.

                    ADD:4th Floor, No. 786 Xinluo Street, Gaoxin Zone,Jinan,Shandong,China.

                    Post code: 250101

                    Website: :810/

                                  http://sdxk.en.china.cn/