XK-JCG10A Machine Tool Control Circuits Training and Evaluation Equipment for Shool Lab and Electrical training

1. Product overview:

XK-JCG10A Typical machine tool control circuits training and evaluation device adopt standard electricity cabinet as the main cabinet and make rational use of the double-sided space of cabinet. Each cabinet has four different kinds of machine circuits and the front is X620W universal milling machine control circuit and horizontal type of T68 boring machine control circuit, the reverse side is Z3040 radial drilling machine control circuit and C6140 center lathe control circuit. The device is equipped with leakage and short-circuit protection and emergency switch to guarantee the students’ safety. This training evaluation device adopt CAN bus intelligent evaluation system and thus to evaluate the training, each machine is equipped with 10 more reference fault points for teachers to select and refer to.

2. Technical indicator:

2.1 Size: 900mm*500mm*1850mm, weight: 150KG

2.2 Power supply: AC380V±5% three phase five wires 50Hz, <15A

2.3 Three phase power supply main switch with leakage protection IΔn<30mA, time<0.1S

2.4 With accident sudden stop button, power source indicator, power indicator

3. Experimental bench accessories

3.1 Experiment guide wire 20 pcs

3.2 Experiment manual 1 book

4. Experiment list

4.1 CA6140 machine tool

1) Lighting lamp is not on

2) Fast forward motor still

3) Power supply fault, vehicle no electricity

4) Cooling pump non work

5) Control circuit non work

6) Cooling pump and fast forward motor not work

7) The spindle motor non self lock

8) Single lamp not light

9) Spindle non start

4.2 X62W universal milling machine

1. Power is failure and vehicle is not power on

2. Spindle does not have speed change impulse

<![if !supportLists]>3.<![endif]>Cooling pump does not work

<![if !supportLists]>4.<![endif]>Feeding motor does not work

<![if !supportLists]>5.<![endif]>Spindle motor does not have reverse braking

<![if !supportLists]>6.<![endif]>Spindle motor does not self-locking

<![if !supportLists]>7.<![endif]>Spindle motor cannot be activated

<![if !supportLists]>8.<![endif]>Working platform does not have speed change impulse

<![if !supportLists]>9.<![endif]>Working platform does not have fast-forward

<![if !supportLists]>10.<![endif]>Working platform cannot move to front, back, up and down

<![if !supportLists]>11.<![endif]>Working platform cannot feed automatically and quickly

12. Spindle does not have variable speed impulse

4.3 Z3040 radial drilling machine

1. HL1 of spindle running indicator is not bright

2. Spindle cannot be activated

3. Spindle cannot self-locking after being activated

4. Swing arm cannot go up and down, column and spindle box cannot clamp

5. Swing arm, column and spindle box cannot clamp after being loosened

6. Swing arm cannot go up and down

7. Column and spindle cannot clamp after being loosened

8. Swing arm cannot go up

9. Swing arm cannot rise

4.4 T68 boring machine

1. Main power is not power on

2. Spindle motor cannot be activated by positive and negative rotation

3. Spindle motor can be activated in only one direction and can not be activated in another direction

4. When spindle motor is in high-gear, it does not shift to high-gear but stop automatically after activated in low velocity.

5. Spindle motor cannot be activated in low-gear, when in high-gear and after pressed the button. it does not activate until delayed for a few seconds

6. AC contactor cannot self-locking

7. AC contactor cannot interlocking

8. Emerge a short time reverse rotation after spindle stopped

9. Does not have braking function when spindle stopping

10, Light is not bright.