Tiancheng: Always walk in the forefront of the industry

Ultra-resistant water jet nozzle

Any of the parts in high pressure abrasive water jet cutting system corrosion caused by wear will affect the normal operation of the whole system, the development hard materials of long life and more resistant product is a guarantee of equipment operation for a long time. Now, more than 70% customers in China are using tiancheng’s nozzles. Choose TC nozzle as a replacement parts for you is the best choice.

Key Features:

 Endurance life

Stability

Ultra Wear Resistant, ultra-highhardness

Minimum of water, abrasive consumption

Faster cutting speed

A longer service life of quality

Overall superior performance

Outstanding performance:

superior abrasion resistance means that you will no longer need frequent replacement of nozzle.

Longer use life will bring you optimization jet pattern and speed improvements. So, faster average cutting speed, time to replace nozzle and cutting head calibration operation time will be substantially reduced.

While cutting accuracy will improve, uninterrupted cutting capacity enhancement. If there is no high-performance nozzle, abrasive water jet cutting’s advantages will be greatly reduced, also the amount of water and abrasive will be increased.

Due to need check , replace nozzle and test the performance, then it will take a long time for the whole system recover overload production. will lead downtime increased. The key factor to effect nozzle cutting efficiency is its wear resistant.  If keep the most efficiency cutting pattern and speed, the whole cutting systerm’s production capability and quality will be improved. Although you buy abrasive water cutting system under a higher investment, but you will get double in return.

Besides, TC nozzle inner diameter high precision, high-quality finish and concentricity are also a big advantage

TC nozzle suitable for domestic and overseas abrasive water jet cutting device, completely independent production, but also adequate inventory

It should be noted the following three questions:

1. Alignment of components

The orifice, mixing chamber and abrasive nozzle must be precisely machined and fit perfectly together to avoid damage of consumables by the waterjet stream.

2. Check if any damage for the orifice

3. Check if any damage for the Mixing Chamber

orifice and nozzle are alignment, otherwise will easily cause the wear of nozzle.  To prolong the use life of nozzle, need to make them alignment by water and make sure the water stream in the center before working. Rotary nozzle 120 degree will increase the degree of centripetal abrasion.

If water stream is not in the center, it will directly impact nozzle inwall, then cutting speed and quality will lower, and it’s use life will be shorter. The stream not in center will cause the abrasion of the nozzle deep inwall. Observe entrance, shows the trail like S shape.

To make sure nozzle and orifice alignment, need precision machining parts

and Clean, dust-free assembly environment.  TC nozzle can meet the requirement which have concertricity out and inner diameter.

The normal nozzle abrasion present centripetal continuous wave abrasion trail from entrance to exit. Accurate alignment nozzle maximum prolong the use life of nozzle and improve cutting speed and quality. As you know longer of the nozzle or smaller inner diameter, harder accurate alignment.

TC Diamond cutting head

TC diamond cutting head has stability performance and productivity leap. Through the empirical analysis and extensive testing, It can bring you more convenience in practice.

---- Combination of diamond cutting head

Insert the diamond to avoid the concentricity is differ from ruby damage and wear. Eventually improve the quality of the trimming and cutting speed. The service life of abrasive nozzle is increased by 20%.

----TC Diamond nozzle technology

Each diamond series products have the guarantee of 500 hours. Only diamond series can let the customer through the diamond in this field to obtain the accurate and convenient. And there is no need to involve the whole cutting head.

----The Improved nozzle clamping nut design

Extended nozzle with excellent tolerance, maximize the improvement of the nozzle concentricity and longevity. Another TC tiancheng bit unique is that it can easily remove the damaged nozzle

Detail Specifications

* short-term available

details photos:

1.more than 10 years manufacture experience in tungsten carbide

2.Implement strict quality testing and control procedure to make superior quality. (ISO9001)

3.we can accept all kinds of international payment.(L/C, D/A,D/P,T/T, Paypal,western union,money gram, etc.)

4.we can accept all trade terms

5.Reply your inquiry within 10 hours

6.We are professional factory, so our price is lower than others

7.Professional sales person

8.Perfect Oral English communication service

factory and some machines of rods: