WLAN, buy Huawei AC6005 14 Gbit/s forwarding capability Access Controller on China Suppliers Mobile

Product Details

Huawei AC6005 14 Gbit/s forwarding capability Access Controller

Appearance

Ports

1. MODE button: switches working mode of indicators.

2. Six 10/100/1000BASE-T Ethernet electrical ports

3. Two combo ports

4. Console port

5. USB port

Indicator Description

The AC6005-8-PWR has the same indicators on the front panel as the AC6005-8 except that the AC6005-8-PWR has a PoE indicator. The following uses the appearance of the AC6005-8-PWR as an example.

No.	Indicator/Button	Status	Description
1	Power supply indicator: PWR	Off	The AC6005-8-PWR is powered off.
		Steady green	The power supply is working properly.
		Steady orange NOTE:Only the PWR indicator on the AC6005-8-PWR displays orange.	The PoE power supply is faulty.
2	System status indicator: SYS	Off	The system is not running.
		Green	Fast blinking: The system is starting. Slow blinking: The system is running properly.
		Steady red	The system cannot start normally, or an overheat alarm or fan alarm is generated.
3	State mode indicator: STAT	Off	The state mode is not selected.
3	State mode indicator: STAT	Steady green	The service port indicator works in the default mode (STAT). In this mode, the indicator indicates the port status.
4	Speed mode indicator: SPED	Off	The speed mode is not selected.
4	Speed mode indicator: SPED	Steady green	The service port indicator indicates the port speed. After 45 seconds, the service port indicator automatically restores to the default mode (STAT).
5	PoE mode indicator: PoE NOTE:Only the AC6005-8-PWR has this indicator.	Off	The PoE mode is not selected.
5		Steady green	The service port indicator indicates the PoE status of each port. After 45 seconds, the service port indicator automatically restores to the default mode (STAT).
6	Mode switching button: MODE	-	AC6005-8-PWR: When you press the button once, the SPED indicator turns green and the service port indicators indicate the speed of the ports. When you press the button for a second time, the PoE indicator turns green and the service port indicators indicate the PoE status of the ports. When you press the button for a third time, the STAT indicator turns green. AC6005-8: When you press the button once, the SPED indicator turns green and the service port indicators indicate the speed of the ports. When you press the button for a second time, the STAT indicator turns green. If you do not press the button within 45 seconds, the indicators restore to the default mode. That is, the STAT indicator turns green, and the SPED and PoE indicators are off.
7	Service port indicator GE electrical ports: The first indicator indicates the status of the bottom left port. The indicators correspond to the ports from bottom to top and from left to right. GE optical ports: Each optical port has a corresponding indicator above it.	Descriptions of service port indicators vary in different modes. For details, see the following table.

Mode	Status	Description
STAT	Off	No link has been established to the port or the port has been shut down.
STAT	Green	Steady on: A link has been established to the port. Blinking: The port is sending or receiving data.
SPED	Off	No link has been established to the port or the port has been shut down.
SPED	Green	Steady on: The port is working at 10 or 100 Mbit/s. Blinking: The port is working at 1000 Mbit/s.
PoE NOTE:Only the AC6005-8-PWR has this indicator.	Off	The port is not providing PoE power.
	Steady green	The port is providing PoE power.
	Orange	Steady on: The PoE function is disabled on the port. Blinking: The port stops providing PoE power because a fault occurs, for example, an incompatible powered device (PD) is connected to the port.
	Blinking green and orange	The port cannot provide PoE power due to any of the following reasons: The power of the PD exceeds the power supply capability of the port or exceeds the threshold. The overall output power has reached the maximum output capability of the device. The PoE power function is not enabled on the interface in manual power-management mode.

Switching and forwarding features

Feature		Description
Ethernet features	Ethernet	Operating modes of full duplex, half duplex, and auto-negotiation Rates of an Ethernet interface: 10 Mbit/s, 100 Mbit/s, 1000 Mbit/s, and auto-negotiation Jumbo frames Link aggregation Load balancing among links of a trunk Interface isolation and forwarding restriction Broadcast storm suppression
	VLAN	Access modes of access, trunk, and hybrid Default VLAN
	MAC	Automatic learning and aging of MAC addresses Static, dynamic, and blackhole MAC address entries Packet filtering based on source MAC addresses Interface-based MAC learning limiting
	ARP	Static and dynamic ARP entries ARP in a VLAN Aging of ARP entries
	LLDP	LLDP
Ethernet loop protection	MSTP	STP RSTP MSTP BPDU protection, root protection, and loop protection Partitioned STP
IPv4 forwarding	IPv4 features	ARP and RARP ARP proxy Auto-detection NAT Bonjour Protocol
	Unicast routing features	Static route RIP-1 and RIP-2 OSPF BGP IS-IS Routing policies and policy-based routing URPF check DHCP client, server and relay DHCP snooping
	Multicast routing features	IGMPv1, IGMPv2, and IGMPv3 PIM-SM Multicast routing policies RPF
IPv6 forwarding	IPv6 features	ND Protocol
	Unicast routing features	Static route RIPng OSPFv3 BGP4+ IS-IS IPv6 DHCPv6 DHCPv6 Snooping
	Multicast routing features	MLD MLD Snooping
Device reliability	BFD	BFD
Layer 2 multicast features	Layer 2 multicast	IGMP snooping Prompt leave Multicast traffic control Inter-VLAN multicast replication
Ethernet OAM	EFM OAM	Neighbor discovery Link monitoring Fault notification Remote loopback
QoS features	Traffic classification	Traffic classification based on the combination of the L2 protocol header, IP 5-tuple, outbound interface, and 802.1p priority
	Action	Access control after traffic classification Traffic policing based on traffic classification Re-marking packets based on traffic classifiers Class-based packet queuing Associating traffic classifiers with traffic behaviors
	Queue scheduling	PQ scheduling DRR scheduling PQ+DRR scheduling WRR scheduling PQ+WRR scheduling
	Congestion avoidance	SRED WRED
Configuration and maintenance	Terminal service	Configurations using command lines Error message and help information in English and Chinese Login through console and Telnet terminals Send function and data communications between terminal users
	File system	File systems Directory and file management File uploading and downloading using FTP and TFTP
	Debugging and maintenance	Unified management over logs, alarms, and debugging information Electronic labels User operation logs Detailed debugging information for network fault diagnosis Network test tools such as traceroute and ping commands Interface mirroring and flow mirroring
	Version upgrade	Device software loading and online software loading BootROM online upgrade In-service patching
Security and management	System security	Different user levels for commands, preventing unauthorized users from accessing AC6005 SSHv2.0 RADIUS and HWTACACS authentication for login users ACL filtering DHCP packet filtering (with the Option 82 field) Defense against control packet attacks Defenses against attacks such as source address spoofing, Land, SYN flood (TCP SYN), Smurf ping flood (ICMP echo), Teardrop, and Ping of Death attacks IPSec
Security and management	Network management	ICMP-based ping and traceroute SNMPv1, SNMPv2c, and SNMPv3 Standard MIB RMON

AP Management Specifications

Feature	Specifications
AP access control	Displays MAC addresses or SNs of APs in the whitelist. Adds a single AP or multiple APs (by specifying a range of MAC addresses or SNs) to the whitelist. Automatically discovering and manually confirming APs. Automatically discovering APs without manually confirming them.
AP region management	Supports three AP region deployment modes: Distributed deployment: APs are deployed independently. An AP is equivalent to a region and does not interfere with other APs. APs work at the maximum power and do not perform radio calibration. Common deployment: APs are loosely deployed. The transmit power of each radio is less than 50% of the maximum transmit power. Centralized deployment: APs are densely deployed. The transmit power of each radio is less than 25% of the maximum transmit power. Specifies the default region to which automatically discovered APs are added.
AP profile management	Specifies the default AP profile that is applied to automatically discovered APs.
AP type management	Manages AP attributes including the number of interfaces, AP types, number of radios, radio types, maximum number of virtual access points (VAPs), maximum number of associated users, and radio gain (for APs deployed indoors). Provides default AP types. Supports user-defined AP types.
Network topology management	Supports LLDP topology detection.

Radio Management Specifications

Feature	Specifications
Radio profile management	The following parameters can be configured in a radio profile: Radio working mode and rate Automatic or manual channel and power adjustment mode Radio calibration interval The radio type can be set to 802.11b, 802.11b/g, 802.11b/g/n, 802.11g, 802.11n, 802.11g/n, 802.11a, 802.11a/n, or 802.11ac. You can bind a radio to a specified radio profile.
Unified static configuration of parameters	Radio parameters such as the channel and power of each radio are configured on the AC and then delivered to APs.
Dynamic management	APs can automatically select working channels and power when they go online. In an AP region, APs automatically adjust working channels and power in the event of signal interference: Global calibration: The optimal working channel and power of a specified AP can be adjusted. Partial calibration: The optimal working channels and power of all the APs in a specified region can be adjusted. When an AP is removed or goes offline, the AC6005 increases the power of neighboring APs to compensate for the coverage hole. Automatic selection and calibration of radio parameters in AP regions are supported.
Enhanced service capabilities	The AC supports 802.1a/b/g/n/ac. These modes can be used independently or jointly (an, bg, bgn, and gn). The AC preferentially uses the 5 GHz frequency band for STAs. 2.4 GHz and 5 GHz frequency load balancing

WLAN Service Management Specifications

Feature	Specifications
ESS management	Allows you to enable SSID broadcast, set the maximum number of access users, and set the association aging time in an ESS. Isolates APs at Layer 2 in an ESS. Maps an ESS to a service VLAN. Associates an ESS with a security profile or a QoS profile. Enables IGMP for APs in an ESS.
VAP-based service management	Adds multiple VAPs at a time by binding radios to ESSs. Displays information about a single VAP, VAPs with a specified ESS, or all VAPs. Supports configuration of offline APs. Creates VAPs according to batch delivered service provisioning rules in automatic AP discovery mode.
Service provisioning management	Supports service provisioning rules configured for a specified radio of a specified AP type. Adds automatically discovered APs to the default AP region. The default AP region is configurable. Applies a service provisioning rule to a region to enable APs in the region to go online.
Multicast service management	Supports IGMP snooping. Supports IGMP proxy.
Load balancing	Performs load balancing among radios in a load balancing group. Supports two load balancing modes: Based on the number of STAs connected to each radio Based on the traffic volume on each radio

QOS

Feature	Specifications
WMM profile management	Enables or disables Wi-Fi Multimedia (WMM). Allows a WMM profile to be applied to radios of multiple APs.
Traffic profile management	Manages traffic from APs and maps packet priorities according to traffic profiles. Applies a QoS policy to each ESS by binding a traffic profile to each ESS.
AC traffic control	Manages QoS profiles. Uses ACLs to perform traffic classification. Limits incoming and outgoing traffic rates for each user based on inbound and outbound CAR parameters. Limits the traffic rate based on ESSs or VAPs.
AP traffic control	Controls traffic of multiple users and allows users to share bandwidth. Limits the rate of a specified VAP.
Packet priority configuration	Sets the QoS priority (IP precedence or DSCP priority) for CAPWAP control channels. Sets the QoS priority for CAPWAP data channels: Allows you to specify the CAPWAP header priority. Maps 802.1p priorities of user packets to ToS priorities of tunnel packets.
Airtime scheduling	Allocates equal time to users for occupying the channel, which improves users' Internet access experience.

WLAN Security Specifications

Feature	Specifications
WLAN security profile management	Manages authentication and encryption modes using WLAN security profiles. Binds security profiles to ESS profiles.
Authentication modes	Open system authentication with no encryption WEP authentication/encryption WPA/WPA2 authentication and encryption: WPA/WPA2-PSK+TKIP WPA/WPA2-PSK+CCMP WPA/WPA2-802.1x+TKIP WPA/WPA2-802.1x+CCMP WAPI authentication and encryption: Supports centralized WAPI authentication. Supports three-certificate WAPI authentication, which is compatible with traditional two-certificate authentication. Issues a certificate file together with a private key. Allows users to use MAC addresses as accounts for authentication by the RADIUS server. Portal authentication: Allows an AC to function as a portal gateway. Prohibits an AC from functioning as a portal gateway. Supports only Layer 2 portal.
Combined authentication	Combined MAC authentication: PSK+MAC authentication MAC+portal authentication: MAC authentication is used first. When MAC authentication fails, portal authentication is used. This type of authentication applies only to centralized forwarding.
AAA	Local authentication/local accounts (MAC addresses and accounts) RADIUS authentication Multiple authentication servers: Supports backup authentication servers. Specifies authentication servers based on account. Configures authentication servers based on account. Binds user accounts to SSIDs.
Security isolation	Port-based isolation User group-based isolation
WIDS	Rouge device scan, identification, defense, and countermeasures, which includes dynamic blacklist configuration and detection of rogue APs, STAs, and network attacks.
Authority control	ACL limit based on the following: Port User group User
Other security features	SSID hiding IP source guard: Configures IP and MAC binding entries statically. Generates IP and MAC binding entries dynamically.