6KW 110V Voltage 50A Current Adjustable DC Power Supply

Specification sheet

 

Product model: AITOP-6KW-110

Output power: 6000W110V50A, input voltage: three-phase AC380V±20%, frequency 50Hz

Voltage output regulated value 0-110V continuously adjustable, output regulated current value 50A. Voltage and current dual display

Dimensions depth, width and height: 590*270*180mm, weight 25kg

Output regulated voltage value adjustable range: usually rated value 15%-rated value continuously adjustable (customizable 0V start adjustment);

Output constant current value adjustable range: usually rated value 15%-rated value continuously adjustable (customizable 0A start adjustment);

Protection function: input overload circuit breaker protection, output overvoltage protection, output overcurrent protection, output short circuit protection, output power protection, overheating protection, whole machine overheating protection threshold 80-85℃.

Mean time between failures ≥50000H.

Environmental conditions: working temperature (-20℃-50℃), storage temperature (-40℃-70℃), relative humidity 90% (40±20C), atmospheric pressure (70-160) KPA.

Rise time: 50ms at full load (typical value)

Hold time: 20ms at full load (typical value)

Power supply voltage regulation rate: voltage regulation ≤0.5%;

Load regulation rate: voltage regulation ≤2%; constant current ≤3%;

Ripple voltage: Vpp≤1%;

Output voltage: display accuracy ±1%; output current: display accuracy ±2%;

Insulation resistance: input-output: ≥20MΩ; input-casing: ≥20MΩ; output-casing: ≥20MΩ;

Insulation strength: input-output: AC1500V, 10mA, 1 minute;

Input-casing: AC1500V, 10mA, 1 minute;

Output-casing: AC500V, 10mA, 1 minute.

Cooling fan: The temperature-controlled fan starts automatically at 40-45 degrees.

 

 

Picture 1 Front side                                     Picture 2 back side

Display meter: Display voltage and current,

Rotary switch: Adjust voltage and current

 

2. Product Features:

Adopting switching power supply technology without power frequency transformer, it has AC and DC compatible input function and wide input voltage range; adopting advanced switching power supply control technology and components, as well as careful design, the whole machine is small in size, light in weight and high in efficiency, ensuring the stability and reliability of long-term full-load operation.

The output voltage value (output voltage when output current

It has perfect protection functions. Built-in temperature-controlled cooling fan can effectively dissipate heat and effectively extend the life of the fan; overheating automatic shutdown protection; output overvoltage, overcurrent and short circuit protection. Power-on delay soft start to avoid overshoot at startup.

Main uses: Widely used in power DC panel systems, industrial control, electronic power, electroplating, communications, scientific research, instrumentation, military industry, medical treatment, ships, railways, battery charging and other high-tech fields

III. Brief description of working principle:

The input voltage of AC or DC passes through the "input notch" circuit to the "rectifier filter" circuit to obtain a high-voltage DC voltage. "Power conversion" converts high-voltage DC into high-frequency AC, which is converted to the required output voltage through a high-frequency transformer, and then the output voltage is obtained through high-frequency rectification and filtering. The control circuit samples the output voltage and output current, and generates a pulse width modulation (PWM) signal after closed-loop feedback to control the "power conversion" circuit to keep the output voltage or current stable.

The "auxiliary power supply" is also composed of a switching power supply. Since the industrial frequency transformer is completely eliminated, it has AC and DC compatible input functions. The output voltage regulation and constant current are controlled from the output side to ensure stability and reliability. The "protection circuit" provides fan temperature control, overheating protection, output overvoltage, overcurrent and short circuit protection.

4. Operation method and precautions:

Unpacking: Check the accessories in the box when unpacking.

Check before powering on: Check the damage of the power supply that has been stored and transported before powering on, such as whether the screws are loose, whether the appearance is abnormal, whether the power cord and terminal are shaken off, and whether they are damp, etc. If the above phenomena occur, they should be handled promptly and properly.

There is a delay of (1 to 5) seconds when starting the machine. Before operation, the required output voltage should be pre-adjusted when the output end is not connected to a load, or the output voltage should be checked first, or the "voltage adjustment" potentiometer should be pre-adjusted to the minimum; the connected power cord should ensure that sufficient current can pass through, and the cross-sectional area of the copper wire of the input power cord for every 1 kilowatt of input power should be no less than 0.75mm²; the positive and negative poles of the output line are determined according to the length of the output line and the current passing through, usually the cross-sectional area of the copper wire for every 3-6A current is 1mm²; when the cross-sectional area of the output line is not enough, multiple lines can be connected in parallel to meet the required requirements; the wiring should be connected to the safety ground wire and the input power line according to the mark on the rear baffle, and confirm that the connection is correct and the joint is firm. Pay attention to whether the voltage of the input power supply connected to the customized specification power supply is consistent with the nominal voltage in the manual.

Good Quality 110Volt 50A /150V90A 12V-1500V OPTION 2KW 3KW 4KW 6KW 8KW 10KW 12KW 15KW DC adjustable Power Supply

aitop 

We provide all kind of lithium battery pack assembly machines and solutions with good quality and services. 

Our products including:

1.IR tester

2.Capacity tester for cylindrical &prismatic&polymer cells

3.BMS tester

4.Sorting machine for common use

5.Insulation paper sticker machine

6.Manual spot welding machine

7.Automatic spot welding machine

8.Battery pack integrated tester

9.Battery pack charging discharging aging machine

10.PVC shrinking machine

11. Nickel plate&PVC cutting machine

12.Laser welding machine

13.Wire bonding machine and etc.

All of our products are good price. 

If you have any interesting,please feel free to contact with us

 Aitop machines for li-ion Batteries assemble are intelligent, simple to learn, easy to operate, our after-sales service team are professional and efficient, one-to-many instructions for operation, many-to-one analysis and solve problems, one-to-one training, if you require ,(option)we can also arrange professional after-sales personnel to your factory to install the machines and training .One-year warranty and lifetime maintenance are our guarantee of quality .we had sale machines to India, Bangladesh, USA, UK, Korea, Japan.at present, we have professional and exclusive after-sales teams in China, India , which can arrange after-sales in time.

Absolutely,choosing our machine is the most correct choice for you. Welcome to visit our factory

Thanks and Best regards

Jenny (Manager) 

Cel/whatsapp/wechat: +86-18098919495