Cold flying saw
USD $25000 - $35000 /Set
Min.Order:1 Set
Tangshan Yifei Trading Co.,Ltd
High-precision flying cold saw adopts Siemens' most advanced digital motion control system, which has short response time of multi-axis control, flexible acceleration and deceleration, and perfects the high-precision synchronous tracing sawing of steel pipes.
The flying cold saw bases is equipped with inlet guide rollers (upper and lower, left and right rollers), the front end of the fixture is equipped with auxiliary guide rollers, and the final discharge position is provided with supporting rollers, all supporting rollers help the parallel movement of the pipe in the sawing process. Both ends of the saw body are equipped with car safety bumpers. Sawing method: Saw blade and feed can be adjusted, that is to say, feed servo motor speed can be changed, saw blade speed can be changed, thus greatly improving the utilization rate of saw blade.
Advantages
Safety
Low noise, good production environment, low spindle rotation and high safety factor
Excellent performance and high production efficiency
The cutting has good flatness, no burr, no need for flat head or CNC cutting, high cutting efficiency and low loss.
Intelligent operation
Friendly operate interface, clearer and simpler control, richer information, and simple settings for excellent cutting results.
Low maintenance costs
Flat cut, no burr, no secondary processing, stable equipment performance, optimized operating curve to ensure minimum mechanical wear, reduce downtime, and lower average cost.
Flying cold saw through the 4G network, it realizes 24-hour remote online diagnosis, fault inquiry, fault repair, program update and download functions, and realizes unattended after-sales service for users. Efficiently and quickly solve the worries behind.
Other type ordinary hot cut flying saw
The noise is high, the production environment is bad, the spindle speed is high, the safety factor is low, and safety accidents are easy to occur.
The cutting burr is large, requires flat head, pneumatic or hydraulic drive cutting, low cutting efficiency and large loss.
There is less information on the operation interface, it is difficult to judge the state of the device, and the cutting effect cannot be changed.
The cut burr is large, secondary processing is necessary. The mechanical equipment has large impact, easy to form wear, increase downtime, and the subsequent average cost is high.
Main functions
Key features
Operational
Following the traditional combination of internal and external operations, the operation interface is simple and clear, and after simple training, the on-site staff can operate the system.
Large amount of data storage and long time
All commissioning parameters can be saved in recipes and can be saved in multiple groups. Effectively prevent field workers from inadvertently modifying parameters or erroneously deleting parameters, resulting in loss of parameters.
Debug screen upgrade
The newly added debugging screen not only facilitates the debugging of the commissioning personnel, but also facilitates the parameter setting and debugging of the field staff when replacing or maintaining the equipment.
Tube selection screen
With intelligent calculation, only the on-site staff needs to select the type of pipe to be produced according to the actual situation, which greatly saves on-site management time.
System trend graph is more realistic
The communication rate is improved, and the trend graph of the system is more realistic, delicate, and truly reflects the operation of the system, providing a powerful basis for the efficient operation of the system.
Three models are available
When booting into manual mode and entering simulation or automatic mode, if the conditions are not met, an error message will pop up to facilitate the on-site staff to quickly discharge the fault and save debugging time.
Use
Flying cold saw is suitable for online high-speed cutting of all kinds of ERW pipes, using high-speed steel or TCT alloy saw blade for cutting.
Specification
Model | 76 cold flying saw | |
Cutting material | Q195,Q235 | |
Tensile strength | Less than 400N/mm2 | |
Steel pipe size | Round pipe | Dia 32-89mm |
Square pipe | 25-70mm | |
Rectangular pipe | Max 45x90mm | |
Pipe thickness | 1.0-4.0mm | |
Cut to length | 1500-99000mm | |
Production speed | Max 100m/min | |
Motor configuration | Drive | Italy PHASE |
Cutting | Siemens AC motor/servo | |
Feeding | Siemens | |
Saw blade type | HSS/TCT |