Explosion proof Fluorescent Light Replacement for Zone 1 Zone 21 Hazardous Areas

 

Replacement of traditional explosion-proof lamp, traditional explosion-proof three-proof lamp

Power:20W/30W/40W/50W/60W/70W/80W/100W

Model No. CES-EX-LN-02P Series (ATEX / IECEx)

LN-02P is one explosion proof led linear fixture to replace the traditional explosion-proof fluorescent light and explosion-proof tri-proof light. High lumen, less power, save energy. High strength aluminium alloy enclosure, impact and vibration resistant. High light-transmission PC cover reduces direct visual contact with the light source. Special powder spraying treatment can for corrosive environments..

 

application range:

CES-EX-LN-02P is primarily used to replace conventional explosion-proof fluorescent lamps for Class I Zone 2, Groups A, B, C and D, with high lumen luminous flux, which can be used for general area lighting in wastewater treatment, oil and gas refineries, petrochemical facilities, food and beverage facilities, tunnels, outdoor wall and column installations.

 

Features:

l  High light efficiency: up to 140 LPW；

l  CCT: 3000K / 4000K / 5000K / 6500K；

l  -40 °C to + 55°C ambient operating temperature

l  Optical reflector: uniform illumination

l  caliber: 3/4 "-14 NPT, M25 X1.5-6H or M26 X1.5-6H;

 

Standard material：

Housing - Aluminum alloy (ADC12 and 6063)；

Lenses - polycarbonate (PC)；

 

 Installation (to be ordered separately) :

l  Multiple installation options：

l  lifting frame 

l   wall-mounted installation

l  Installation Angle: 0° to ±60°；

 

Certification and Safety：

NEC / CEC:

Class I, Division 2, Groups A, B, C and D;

T-Class: T *:

Damp and wet locations

Certificate NO.: E475887-UL-CUL

 

Certification Standard：

US:  UL 844; UL 1598;

Canada: CSA C22.2 No. 137; CSA C22.2 No. 250.0;

CES-EX-LN-02P  explosion proof LED Lamp parameters

Model	Power	Input voltage：AC100-240 / 277V; Frequency：50 / 60Hz;
		CCT：3000K / 4000K / 5000K / 6500K
		Power factor：0.97
		Light Luminous（LM）	Light Efficacy（Lm / W）	LED Chip	LED Type	Weight （kilogram）	Leight （meter）
CES-EX-LN-02P-75D	75	9000-10500	120-140	288PCS	3030 （6V）	5.5	1.2
CES-EX-LN-02P-65D	65	7800-9100
CES-EX-LN-02P-60D	60	7200-8400
CES-EX-LN-02P-50D	50	6000-7000
CES-EX-LN-02P-40D	40	4800-5600
CES-EX-LN-02P-50B	50	6000-7000		144PCS		3	0.6
CES-EX-LN-02P-40B	40	4800-5600
CES-EX-LN-02P-30B	30	3600-4200

 

Explosion Proof Fluorescent Lighting Replacement - 3ft 4ft - Pole Mount

 

Applications:

• Wastewater treatment，oil and gas refineries, drilling rigs, petrochemical facilities, food and beverage facilities, tunnels, outdoor wall and stanchion mounted general area lighting, and where flammable vapors, gases, ignitable dusts, fibers or flyings are present.
• Applies to hazardous locations of Zone 1 and Zone2 with explosive gas atmosphere.
• Applies to hazardous locations of Zone 21 and Zone22 with explosive dust atmosphere.

ATEX: EN IEC 60079-0-2018; EN 60079-7-2015; EN 60079-18-2015; EN 60079-31-2014;
IECEx: IEC 60079-0-2017; IEC 60079-7-2015; IEC 60079-18-2014; IEC 60079-31-2013;

IECEx & ATEX :

• “CAUTION-USEFASTENER WITH YIELD STRESS ≥ 640 MPa”；

• “WARNING – DO NOT OPEN WHEN ENERGIZED”；

• “WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT”；

• “WARNING – ONLY USE CABLES SUITABLE FOR 85°C”；

• " WARNING - DETAILED TEMPERATURE CLASS - SEE INSTRUCTIONS”；

• “THE FLAMPROOF JOINTS ARE NOT INTENDED TO BE REPAIRED”;

• End user shall use certified cable gland or conduit with suitable type of protection for final installation purpose；

• External earthing wire shall be connected when used and the cross-sectional areashall be more than 4mm2 or 10AWG；

• Under rating condition, maximum temperature on the luminaire’s shell shall not be higher than 130℃ for T4.Temperature at cable inlet shall not be higher than allowable limit of the cable applied, to ensure the cable operation normally. The branch point is 83.6℃ and cable entry point is 69.4℃