Specifications:
GD-5L-A2 automatic water bottle blowing machine
CE approval
Speed: 800-1200pcs/h for 5000ml pet bottle
Volume:3000ml-5000mL

Brief introduction of water bottle blow molding machine:

GD-5L-A2 Full automatic blow molding machine is suitable for producing PET/PE and PP plastic containers and bottles in all shapes. It is widely used to produce the carbonated bottle, mineral water, pesticide bottle oil bottle cosmetics, wide-mouth bottle and hot fill bottle etc.

 

Features of main body:

1). Stable performance with advanced PLC.

2). Automatic preform conveyer to save human cost.

3). Preform self-rotation and infrared pre-heater revolution assure the even distribution of heat, which improve the bottle shaping rate, increase the production.

4). High adjusting performance to enable preheat the preforms perfectly by adjust the voltage control area in the PLC, which could adjust the temperature of the infrared lights in the pre-heater, and keep the proper temperature and humidity invariable.

5). High safeties with security automatic-locking device in each mechanical action, which will make the production into a perfect safe environment, in case of the breakdown in certain procedure.

6). Introduce the FESTO air cylinder to avoid contamination and noise.

7). Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.

8). Strong clamping force with high pressure and double crank links to lock the mould.

9). Two ways of operating: automatic and manual.

10). Safe,reliable and unique design of the position of valve to make the pneumatic diagram in the machine easier to understand.

11). Low cost,high efficiency,easy operation and maintenance etc, profited from the fully automatic technological process.

12). Ideal cooling system make the finished bottles without any flaws.

13). Easy for you to install,test and start up.

14). Low rejection rate: less than 0.2 percent.

 

Operation:

The standard operation of GD-5L-A2 stretch blow molding machine includes four steps as follow

Step 1. Put the preform into preform container and the conveyor will take the preform to orientation units automatically.

Step 2. Load the preform at neck up to preform holder, and then preform is conveyed into baking tunnel.

Step 3. After heating, preform is conveyed into the blow station, then close the mold, stretch and blow under low pressure and high pressure, exhaust, open the mold.

Step 4. The finished bottle is taken off by automatic discharging system

 

Machine show

 

Servo system option

	1. Feeding preform system: single channel enter preform, use star wheel enter preform, effectively solve the problem of stuck preform and bottle preform wear.
2. Rotating system: use special chain, driven by servo motor, so that the heating unit in the movement of stable, fast positioning, low noise.
	3. Heating system: adopting rotary bottle blowing machine mode heating and conveying, can reduce energy consumption, greatly improve heating speed and quality.
4. Mold system: adopt high pressure mold locking technology, no expansion phenomenon, and clamp mold line is thin. The mold adopts drawer type structure, and is positioned on the back plate of the mold with four fixed pull rods, which can be easily replaced within half an hour.
	5. Stretch and blow system: cycle time of one blow, two blow can be adjusted, according to the customer's different preform and different bottle type, each pull rod can be adjusted separately, high flexibility.
6. Electronic control system: Pneumatic and electrical components adopt international famous brands, touch screen control system is easy to operate, with perfect monitoring and induction settings, with fault diagnosis function, automatic calculation of the report function, know the production efficiency of each shift.

 

Clamping Servo with SEIMENS brand                            Transfer Preforms Servo

 

Stretching Servo	Feeding Performs Servo

 

Main technical parameter:

	ITEM	UNIT	GD-5L-A2
Container	ntainer volume	L	5
	Max.neck diameter	mm	50
	ntainer diameter	mm	180
	ntainer height	mm	340
	Number of cavities		2
	Theoretical output	BPH	1200
Electricity system	Installed power	kw	36
	Max.heating power	kw	32
Compressed air system	Operating pressure	Mpa	0.7
	Low pressure air consuming	M3/min	2.0
	Blowing pressure	Mpa	4.0
	High pressure air consuming	M3/min	2.5-3.2
	Use mould booster		Yes
Chiller water	Pressure	Mpa	30-40
	Temperature	℃	10-12
	Flow rate	L/min	30
Machine	Size(L*W*H)	mm	3500X2100X1900
	Weight	kg	4500

 

Main configuration

 

Our engineer will make 2D drawing for you

 

 

 

 

 

Q1: How to find suitable plastic bottle blow moulding machine or complete water production line?
A1:  Looking for beverage filling machine in www.grandeemachine.en.china.cn 

 

Q2: What's the capacity of plastic bottle moulding machine?

A2: We have full automatic and semi automatic unit with 800BPH to 20000BPH for 5000ml plastic bottle 

 

Q3: How to choose the capacity of blowing machine for water production line?

A3: If you want 600-800BPH for 5000ml water production line, you can choose semiautomatic blowing machine or automatic one cavity blowing machine,if you want 1000-1200BPH, you can choose automatic 2 cavity blowing machine, if you want more bigger capacity, you can send me inquiry, we can give you more professional technical solutions.

 

Q4: Are you a trading company or a manufactory?

A4: We are the manufacture of water/beverage filling machine and water treatment system over 10 years.We just not only sell drinking water machines and other related equipment , Quality is our culture. We have rich experienced engineers with technicians working team , providing good and after-sales service term , professional salesman terms .

 

Q4: Do you have technical support after we purchased your machines?

A4: We will arrange our professional technical to go aboard to your factory, they will help you and teach you how to install and maintenance the machines which you purchased. Or help you to fix machine when it has problems.

 

Q5: If you buy our machines, can you offer us wear-out spare pats?

A5: We provide our high quality machine 2 years guarantee , and we will also offer you 2 years wear-out spare parts for free. Once your machines broken or doesn't work within 2 years and you can't solve it, firstly, we will try to help you to find problems from your words description by phone or other communication tolls. Secondly, if the phone solutions still not work, our engineers will go to your factory to solve it. Meanwhile, they will teach you the related experiences for fixing.  

 

Why choose Grandee machinery