Lab Spinning & Weaving, buy PP Pet Carbon Fiber Double Screw Melt Spinning Device on China Suppliers Mobile

Product Details

Product Description

AT227 Pilot Scale Melt Spinning Machine is a main key equipment in synthetic fibre production. This machine uses high temperature ceramic to heat and melt the polymer sample, and extrude the sample to be liquid trickle from a spinneret under the effect of inert gas pressure, then nascent fibers form under the effect of air cooling. It is specially designed for small batch production test to simulate the field production.

Features

★ Material Melting and Spinning Part

It consists of extruding part, extrusion measuring head, metering pump, spinning system and cross air-blowing device.

1. Extruding Part

* Extruding screw made of high-temperature alloy tool steal with three sections of electric heating, heating power up to 3KW.
* It adopts heating rods to heat and copper bush for heat soaking.
* Independent temperature controlling and adjusting module for each heating section and adjustable temperature range of from
room temperature up to 320℃.
* Programmable temperature controller for each section with PID control and auto-turning to keep the temperature accuracy with
±0.5℃.
* Driven by frequency-variable motor with power of 2.2KW.
* Water-cooling copper coiler at the discharge port to rapid adjust the temperature of the discharge port.

2. Extrusion Measuring Head

* Independent pressure sensor and temperature sensor mounted on the extrusion measuring head, real-time monitor the pressure and temperature.
* Pressure sensor accurate to 0.1N and temperature sensor accurate to ±5℃.

3. Metering Pump

* All of main body of pump, gears and bearings are made of tool steel, high temperature resistant up to 400℃.
* Heating power up to 3KW.
* Applicable liquids of viscosity ≤ 40000Pas and temperature ≤400℃.
* Pump cleaning temperature not more than 450℃.
* Input pressure up to 12Mpa.
* Maximum pressure difference up to 25Mpa.
* Standard flow of 2.4cc/rev.
* Driven by frequency-variable gear motor with power of 320W.
* Real-time acquisition and display of melt pressure and temperature.
* Built-in pressure sensor and temperature sensor in pump.

4. Spinning System

* Crystal fiber heating furnace with heating power up to 3KW;
* Adjustable temperature range from room temperature to 320℃.
* Maximum material filling up to 3L per time.
* Three heating sections, rapid heating, high heat efficiency and excellent heat insulation.
* Barrel made of 316 stainless steel, thickened wall and uniform material heating.
* Barrel adopts full copper bush for heat soaring and uniform heating.
* Solid relay to control heating elements, accurate temperature controlling, durable and no noise.

5. Cross Air-blowing Device

* Water-cooling fan to blow.
* Cool air passes through the halftone of air filter to enter the channel.
* Effective blowing area of 150×

★ Oiling & Winding Part

1. Rotary Oiling Device

* PA6 roll with adjustable opening and closing design, convenient to start and stop at any time.
* Oiler driven by gear motor with power of 450W with variable speed of 300~1000m/min.
* Oil tank made of 304 stainless steel, rust-proof and durable.

2. Hot Rolls

* Diameter of 125mm and length of 125mm.
* With polishing and chroming surface treatment, hard surface and excellent wear resistance.
* Electric induction heating, clean, environment-friendly and low maintenance cost.
* Temperature range from 70℃ to 200℃.
* Independent variable frequency motor with power of 450W to drive for independent speed adjustment.
* Speed range of 100~500m/min.

3.Winding Head

* Rubber friction pulley.
* Speed range from 300m/min to 1000m/min.
* Maximum winding pole size of 120×¢

★ Measuring and Controlling Part

1. Data Monitor

* Real-time monitoring of material temperature and wall temperature.
* Air paths adopts full 304 stainless steel pipes, valves and pressure meter.
* Programmable temperature controller, PID automatic temperature control and programmable temperature controlling for three heating sections.
* PC remote control and interface display of extruding speed, hot roll speed, winding speed, metering pump speed, temperature and other necessary alarm and signal.

2. Over-limit Alarm
When over load, system will shut off the electricity.
* Over temperature alarm.
When over temperature, machine stops heating.
* Extruding pressure over-limit alarm
When extruding pressure beyond the limit, motor stops rotating.
* Metering pump rotation speed alarm
When metering pump rotation speed is away from the set value, auto alarm display.

Specification

Model	AT227
Melt spinning device
Heating power of extruding screw	3KW
Extruding screw diameter	¢25mm
Temperature range	RT~320℃
Temperature accuracy	±0.5℃
Pressure sensor accuracy	0.1N
Melt pump max. temperature	400℃
Flow of melt pump	2.4cc/rev
Spinneret plate	24 holes, hole dia.: 0.1mm Outer diameter: 90mm Material: 316L stainless steel
Max. Power of crystal fiber furnace	3kw
Max. Heating temperature of furnace	320℃
Cross air blow device	150×150mm
Winding system
Speed range of oiling roll	300~1000m/min
Hot roll temperature range	70~200℃
Hot roll diameter	125mm
Hot roll length	125mm
Winding head speed range	300~1000m/min
ding diameter	320mm
Drive system
Drive motor of melt pump	320W
Drive motor of extruding screw	2.2KW
Drive motor of hot roller	450W
Drive motor of oiling system	450W
Temperature control
Temperature control accuracy	±0.5℃
Melt pressure sensor accuracy	0.1N
Material of gas line	304 stainless steel
Power supply	AC220V, 50Hz

Packing & Delivery

Packaging
Size(cm)	110 (L) * 75 (W) * 180 (H)
Weight	500 Kg
Packaging Details	1. The equipment is covered with film is protect it from water vapour during the trip. 2. The box is filled with foam to protect the equipment from impact. 3. Exported wooden box made from plywood, don't need fumigated.

History

Since 1982 with more than 20 years' experience

Warranty

Two Year Warranty for whole product

Training

Video and user manual for training

Onsite service

Installation and training service is available

Testing service

Free sample testing before order is available

Lead time

15 working days lead time for most product

Lily Cheng
Website
Mobile Phone	+86 180 5517 3820
Whatsapp	+86 180 5517 3820
Skype	1933039910@qq.com
Wechat	+86 180 5517 3820

Payment Term	T/T	EXW	30% T/T in advance, paid the balance before shipment
			30% T/T in advance, paid the balance before shipment		FOB
				CFR(C&F)	30% T/T in advance, paid the balance against copy of B/L
				CIF	30% T/T in advance, paid the balance against copy of B/L
		L/C	L/C amount above 50,000 usd, we can accept L/C at sight
		West Union	Amount lower than 5000usd
		West Union	Amount lower than 5000usd
Delivery Time	7~10days after receiving payment for one container