Dual-plunger Melt Spinning Machine For Disassemble-able Structure
Negotiable
Min.Order:1
AT226 Series Plunger-type Melt Spinning Machine is used to carry out the melt spinning of polypropylene, polyester, polyamide and other special materials with plunger metering system. The raw material melts and flows into the plunger-type cylinder. The plunger-type cylinder driven by the servo motor can precisely monitor and control the flow of melt liquid. The melt liquid passes through the filtering plate, distributing plate and then is extruded through the spinneret plate to spin. The spun fiber can be direct wound onto the winding roll or passes through coagulating bath (optional), heat stretching (optional), relax hot setting (optional) and then be wound onto the winding roll.
Sketch for Dual-plunger Melt Spinning Machine
★ Mixing part, coagulating bath, hot stretching and relaxing
heat setting are optional.
★ AT226A Single Plunger Melt Spinning Machine has a
plunger metering part, but no mixing part while AT226B
Dual Plunger Melt Spinning Machine has two plunger
metering parts and mixing part.
★Material feeding part consists of screw feeder and driving motor. The amount of feeding material is adjustable by
adjusting the feeding speed; the stock bin adopts open-able sealing structure with available nitrogen blowing to
protect the raw material;
★ Plunger metering and melting part: material is heated by heating hood to melt and then flows into the plunger-type
cylinder. The forward of plunger is driven by the servo motor to precisely control the flow; multi-section temperature
controlling, real-time display and control the inner pressure and the temperature of material;
★Mixing part to evenly mix materials (only for AT226B);
★Heating hood of cast copper with multi heating sections, rapid to heat and high heat efficiency;
★Stainless steel winding roll, disassemble-able structure;
Model | AT226A | AT226B | ||
Number of plunger metering part | 1 | 2 | ||
Material-feeding part | ||||
Structure | Screw feeder & driving motor Adjust screw speed to control feeding amount | |||
Material | 316L stainless steel | |||
Designed capacity of stock bin | 200ml | |||
Power of driving motor | 200W | |||
Plunger metering part | ||||
Structure | Melting & metering | |||
Cylinder material of plunger pump | 306 stainless steel | |||
Inner diameter | 40mm | |||
Length | 100mm | |||
Designed pressure | 35Mpa | |||
Surface treatment | Nitrogen treatment | |||
Heat power | 2000W | |||
Temperature controlling range | RT+10~450℃ | |||
Controlling accuracy | ±0.5℃ | |||
Heat mode | Heat loop of cast copper | |||
Mixing part | ||||
Motor power | --- | 800W | ||
Reduction ratio of reducer | --- | 1:20 | ||
Speed adjusting method | Frequency control of motor speed | |||
Metering pump | ||||
Operating temperature | ≤450℃ | |||
Heat method | Electric heating | |||
Capacity of pump | 22~30000kmol/hr | |||
Spinning part | ||||
Material of spinneret plate | SUS630 | |||
Number of spinneret orifice | 1 | |||
Number of mesh on filtering plate | 200 | |||
Ratio of length to diameter of spinneret plate | 2.5:1 | |||
Spinning temperature range | Room temperature~320℃ | |||
Max. heat power of furnace | 1.5KW | |||
Winding | ||||
Motor power | 0.4KW | |||
Max. rotation speed | 2800r/min | |||
Size of winding roll | ¢200×200mm |
Payment Item | T/T | EXW | 30% T/T in advance, paid the balance before shipment | ||
FOB | |||||
CFR(C&F) | 30% T/T in advance,paid the balance against copy of B/L | ||||
CIF | |||||
L/C | L/C amount above 50,000 usd, we can accept L/C at sight | ||||
West Union | Amount lower than 50,000usd | ||||
Delivery Time | 7~10 days after receiving payment for one container |
Packaging | ||
Packaging Details | 1. The equipment is covered with film is protect it from water vapour during the trip. 2. The box is filled with foam to protect the equipment from impact. 3. Exported wooden box made from plywood, don't need fumigated. |
Since 1982 with more than 20 years' experience
Two Year Warranty for whole product
Video and user manual for training
Installation and training service is available
Free sample testing before order is available
15 working days lead time for most product
ERIC QIN | ||
Website | ||
Mobile Phone | +86 188 5510 5986 | |
Whatsapp | +86 188 5510 5986 | |
Skype | eric-qlk | |
Wechat | +86 188 5510 5986 |