DC/AC SPD, buy DC 600V power supply spd surge protective device on China Suppliers Mobile

Product Details

DC 600V power supply spd surge protective device

Products Description

DK-20 power supply series modular surge protective device(SPD) is designed according to IEC61643 standard. It is accordance with the criterion of Low-voltage Surge Protective Devices-Part 1: Surge Protective Devices Performance Requirements and Test Method of Low-voltage Power Distribution System. With good sealing, it is designed as module and 35mm DIN-Rail Mounting. With working indication window, temperature control circuit breaker and built-in over-current protective circuit, the modular SPD can release automatically to avoid fire danger when it breaks down. With remote alarm connector, it is convenient for remote monitoring. The main module and the base are replaceable. The lightning protection modes is L-PE, N-PE (2P/4P) or L-N-PE (1+1) / (3+1).

Application Scope

It can be installed in the low voltage power distribution cabinet/box of buildings, to protect all kinds of power equipment in the single (three) phase power distribution system between LPZ1 and LPZ2. Such as:
1) Low voltage general electricity cabinet and or distribution board of buildings.
2) Outdoor electricity cabinet/distribution box.
3) Applicable power supply system: TT, TN, IT.

Product Paramenters

DK-AC series secondary high-current power surge protectors are designed according to IEC and GB standards, applied to the primary power surge protection products of power supply system. The module is standard 35mm rail mounting mode. It has high surge discharge capacity and the maximum discharge current can reach 160kA(8/20μs). It is applied to the first level surge protection of power supply for equipment systems in areas with high lightning risk.
No continuous current problem, leakage current is small. The product is easy to install. Different combinations can be used in single-phase/three-phase power supply lines.

Applicable Power Supply System	TT, TN, IT
Maximum Continuous Operating Voltage Uc	AC 385V/275V
Nominal Discharge Current (8/20µs)	10kA
Maximum Discharge Current (8/20µs)	25kA
Voltage Protection Level Up	≤1.5kV
Leakage Current	≤20uA
Respond Time tA	≤25ns
Indication Method	Indication Window, Turn Red When Malfunction
Remote Alarm Function	Optional
Maximum Connection Wire Range	BVR 25mm2
Method of Installation	35mm Din Rail Mounted
Material of Shell	PC
Flame Retardant Rating of Outer Shell	UL94-V0
Protection Level of Outer Shell	IP20
Working Temperature	–25~＋70℃
Relative Humidity	≤95%

Item No. are available

Item Series	Protection Mode	Installation Location	Dimension(mm)	Item No
DK-20	L-PE, N-PE(2P)	Low-voltage Single Phase Power Distribution Cabinet	369166mm	DK-20 2P
		Low-voltage Single Phase Power Distribution Cabinet	369166mm	L-N-PE(1+1P)		DK-20(1+1)
		L-PE, N-PE(4P)	Low-voltage Three Phase Power Distribution Cabinet	729166mm	DK-20 4P
		L-N-PE(3+1P)	Low-voltage Three Phase Power Distribution Cabinet	729166mm		DK-20(3+1)

Installation and Caution

1) DK-20 modular surge protective device(SPD) can be installed in any place of the single phase AC power line, and mostly be installed in power distribution boxes, power switches and sockets. It shall be connected with the power line in parallel, and shall adopt Kevin Connection, so as to lower the residual voltage.

2) Strip away the surface rubber of input and output terminal, and expose the copper core. Insert the copper core into the hole of the SPD, and make it firm with a screwdriver.

3) The cross-section of the grounding conductor connected with the module SPD indicating alarm shall be at least 16mm2, and the lead wire of the grounding conductor shall be shorter than 1m, and the shorter the better.