Product Details

ASG102 Digital Handheld Signal Generators 2 Channels Car Automotive Signal Generator Kit With CAN data function

Product Description

(1) Button description and main functions:

F1: It's mainly used to switch between first&fourth items.

Or to switch the value of the selected item.

F2: It's mainly used to switch between 2nd&5th items, or

to switch the value of the selected item.

F3: It's mainly used to switch between 3rd&6th items, or

to switch the value of the selected item.

OK: Determine the button for confirmation or save.

:Up button for up selection or value increase.

:Down button for down selection or value reduction.

:Left button to move one item/bit to left.

:Right button to move one item/bit to right.

CH :It's mainly used for switching between channel 1&channel 2

configuration interfaces.

MENU: Mainly used to return to the menu selection interface.

0-9: The number key changes the corresponding digit value to a numeric

key value.

: On/off.

(2) Port description:(Figure 1-1)

CH1&CH2: Channel 1&channel 2 signal output.

CAN: CAN data receiving end.

Figure 1-1

Instrument features:

According to the automotive rules&actual needs of on-site diagnosis, the instrument ummarizes&analyzes the characteristics of existing car signal generators:

1.The signal characteristics can be adjusted in real time: the signal can be adjusted at any time by adjust waveform, amplitude, frequency, missing teeth&other indicators. This feature greatly helps to determination the fault in the vehicle maintenance process.

2.Two-channel waveform signal output can simultaneously output signals of different frequencies, amplitudes and waveforms within two bandwidths.

3.CAN bus function:

It's mainly used to test whether CAN bus of various models is in normal communication. The test rate is 10K, 20K, 33.3K, 50K, 62.5K, 83.3K, 125K, 250K, 500K, 1M.

4.Friendly HMI: the instrument adopts the most simple design idea, 320*240 large-screen liquid crystal display, the display interface logic is clear; the panel operation is clear, which is convenient for the operator to quickly carry out various operations.

5.It looks small&convenient, using over injection molding, good use of feel. The internal components are all imported, users can use it with confidence!

Main interface operation

1. After turned on product, enter main operation interface (Figure 1-2). Press any button (except on/off key), the first item (channel 1) will be selected by default.

2. Then use the “ ” button to switch the selected item.

3. After selecting the item, press the OK button to enter the corresponding configuration interface.

Figure 1-2

Signal generator operation

After booting into the main interface, press the button to select “Channel 1” or “Channel 2”, then press “OK” to enter the signal generator parameter setting interface. The signal generator operation interface is shown in

Figure 1-3 Figure 1-4

Mainly configure output signal parameters such as frequency, amplitude, duty cycle, waveform, X, Y.

1.Waveform selection

Press F1 to select the first item (“Waveform”), then use the “ ”or“ ” key or the direct numeric key to input the value (range 1-5, a total of 5 waveforms) to select the waveform to be output. The serial number can be seen on the display. Corresponding waveform. The waveform&corresponding serial number are as shown below:

2.Setting frequency

Press F2 key to select the “Frequency” item, use the “ ”or “ ”key to select a value of the frequency, and then add or subtract the value by “ ” or “ ” step or change the value by directly using the number keys.

Note: The frequency value ranges from 1HZ to 8000HZ.

3.Set amplitude

Press F3 key to select the “Amplitude” item, use the “ ” or “ ” key to select a certain value of the amplitude, and then use the “ ” or “ ” key to increase or decrease the value step by step of the bit or directly change the value by the number key.

Note: The amplitude value ranges from 0V to 20V.

4.Set duty cycle

5.Set X value

X represents the number of sine waves or square waves.Press F2 key to toggle the “X” item, use the “ ”or “ ”key to select a value of X, and then press the “ ” or “ ” key to step up or subtract the value or change the value directly by the number key.

Note: The X value range is 1-199.

6. Set Y value

Y represents the number of straight lines.Press F3 key to toggle the “Y” item, use the “ ” or “ ”

key to step up or subtract the bit value or change the bit value directly by the number keys.

Note: Y value range is 0-9.

Package

Detail photo