Feature:

Stainless steel mirror plate, also known as 8K mirror plate, through polishing equipment on the surface of stainless steel plate polishing, so that the luminosity of the plate as clear as a mirror.  

Stainless steel plate surface is smooth, has high plasticity, toughness and mechanical strength, acid, alkaline gas, solution and other media corrosion.  Stainless steel plate production principle is stainless steel raw materials with grinding liquid through polishing equipment on the surface of the plate polishing, so that the surface of the plate flat and luminance as clear as a mirror.

Stainless steel mirror plate processing process can be divided into general grinding and fine grinding two ways, then these two ways of processing produced mirror effect which is better?  And this is about to be judged by the brightness of the mirror surface, and the trashhole on the surface of the plate and grinding flowers must be less.  In general, the stainless steel plate in the polishing machine processing, the slower the speed, the number of grinding groups, and the effect will be very good;  When using the polishing equipment for processing of stainless steel plate, sheet is first and foremost to play sand, and then put the stainless steel plate in grinding fluid, including through 8 groups of different degree of grinding head grinding, grinding process is basically on the surface of the stainless steel plate processing, this process is not deep, this step is to go to remove the oxide layer on stainless steel plate surface.  

Stainless steel 8K plate is also known as :(mirror plate, mirror plate, mirror plate) 

(1) varieties: single side, double side two 

(2) luminosity: 6K, ordinary 8K, fine grinding 8K, 10K 

(3) materials:  Select 2B, BA plate of 201/304/316/430 and other materials as the bottom plate, polishing on the stainless steel plate with abrasive liquid through polishing equipment, so that the luminance of the plate is as clear as a mirror.  

(4) The deployment of grinding liquid: water, nitric acid, iron red powder according to a certain proportion of harmony, the general proportion of good, to make the product quality is higher!  

(5) coarse polishing: generally with grinding wheel: 80#120#240#320#400#600# by coarse to fine order, (note: 80# for coarse) this process generally with water grinding, generally with six groups of grinding machine, mainly in order to remove the surface roughness, burr, trudge, etc., there is a certain depth, about within 2C.  The surface is: fine sand, has a certain luminosity!  

(6) fine polishing: as long as the mechanism of wool felt, the higher the density, the better, this process of water, nitric acid, iron powder grinding, generally using ten groups of grinding machine, no depth at all, mainly in order to remove the surface oxidation layer, sand holes, coarse grinding head flower (also called: grinding head flower, grinding head grain) to improve the brightness, highlight the details.  

(7) Washing and drying: this process is cleaned with clean water, the finer the brush, the better the water is, the cleaner the product is, and then it is dried with baking lamp!  

(8) Quality inspection: check the luminosity, the number of eyes, whether there is peeling line, dark bone, scratching, whether the product is deformed, whether the grinding head flower is within the control range, otherwise the product quality is not up to standard.  Paste protective film packing: this process is mainly for the standard finished products, requirements: protective film paste to smooth, can not leak edge, cut neatly, and then can be packed!  

(9) double-sided 8K plate: the process is roughly the same, the difference is that when grinding the first front, first use the same size plate bottom, prevent the reverse scratching, grinding the front side of the protective film, and then the back plate grinding (the process is the same as above) grinding the protective film, and then replace the front layer has been dirty protective film, that is, the finished product.  Because double-sided 8K relative to single-sided: more time-consuming, high cost, so the current market double-sided 8K board is about 3 times the single-sided 8K cost.  

Characteristic products of our company:

1, Stainless steel plate: 

2B stainless steel plate NO.1 stainless steel plate stainless steel mirror plate, stainless steel pattern plate, the other can be processed wire drawing, film, matte, cut round, cut square, polishing and other processes.  

2, Stainless steel coil: 

cold rolled stainless steel coil hot rolled stainless steel coil stainless steel belt.  

3, Stainless steel pipe: 

thick wall stainless steel pipe large diameter stainless steel pipe capillary stainless steel pipe stainless steel welded pipe stainless steel seamless pipe  

Stainless steel decorative tube, also can be processed polishing, fixed size, sandblasting, seamless.  

4, Stainless steel bar: 

round bar, square bar, hexagonal bar.  Surface: bright rod, black rod.  

5, Stainless steel wire:

stainless steel wire, stainless steel electrode.  

6, Stainless steel profiles:

Angle steel, I steel, channel steel, flat steel.  

7, Nickel base alloy Nickel 200/201 Monel400/K500 Hasteeloyc C-4 C-22 C-276, etc.  

Specification:

0.2mm - 80mm*1000mm - 2000mm*2000mm - 9000mm (can be customized according to customer requirements) 

Company introduction:

Our company is a stainless steel plate, coil and stainless steel seamless pipe, welded pipe production and processing of large spot sales company, at the same time agent stainless steel bar, Angle steel, channel steel, etc., its product quality excellent, marketing throughout the country.  Over the years has been committed to the promotion and sales of stainless steel products, perennial distribution of Shanxi Taiyuan Iron and Steel, Shanghai Baosteel,Gansu Jiusteel, Kunshan Dageng, Shanghai Klup, Ningbo Baoxin, Guangzhou Lianzhong, Zhangjiagang Pohang, and other major steel stainless steel. And major steel mills to establish a long-term friendly relations of cooperation. At the same time also operate stainless steel bars, profiles, pipes and the whole plate dismantling business. Stainless steel plate products sales materials are:  SUS201, 202, 304, 316L, 316Ti, 321, 304L, 441, 444, 436, 439, 430, 409L, 410s, 309s, 310S, 904L , 2205, 2507 and other stainless steel materials, products are mainly used in chemical equipment, water treatment equipment, elevators, tableware, kitchen equipment, solar water heater, mechanical equipment, pressure vessels and other industries. Special processing: according to customer's specified open size.  

The use of stainless steel mirror plate:

Mainly used in building decoration, elevator decoration, industrial decoration, facility decoration and other stainless steel products