HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor
HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor
HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

Negotiable

Min.Order:1

Supply Ability:
1000 per Month
Payment Terms:
T/T Credit Card

Ningbo Haofeng Magnet Technology Co., Ltd.

Business Type: Manufacturer
Main Products: Brushless DC Motor ,Brush DC Motor ,Motor Controller ,SmCo magnet

Product Details

Product Display

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

 

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motorHF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

 

 

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

 

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

 

VIEW MORE PLS CONTACT US >>>

 

 

Other Products

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

Process Flow

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor 

About Us

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motorHF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor 

Packing&Transport

HF Manufacturing M05304 Size 230*132*179mm 24v 1100w 1500rpm hall sensor brushless DC motor

Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped. 

      What to do: Replace the fuse or reset the breaker.

 

     Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
     What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.

 

     Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
     What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.

 

      Likely cause: Controller may be defective.
      What to do: Verify voltage is coming out of the controller.

 

Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
     What to do: Verify that the motor is wired correctly.

 

     Likely cause: No output power from controller.
     What to do: Measure voltage coming from the controller.

 

     Likely cause: Motor is damaged and the armature is rubbing against the magnets.
     What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.

 

Q:  Motor takes too long to accelerate,what to do?
A:  Likely cause: Motor controller not properly set.
     What to do: Adjust the acceleration trim pot of the controller.

 

     Likely cause: Brushes are worn.
     What to do: Verify brush length.

 

     Likely cause: Bearings may be defective.
     What to do: Inspect bearings. Noisy or rough bearings should be replaced.

 

Q:  Motor runs in the wrong direction,what to do?
A:  Likely cause: Incorrect wiring
     What to do: Interchange the two motor leads.

 

Q:  Motor runs OK but has a clicking noise,what to do?
A:  Likely cause: Suspect a burr on the commutator.
     What to do: Remove burr from commutator using a commutator stone.

Contact Supplier

You May Like

New Products

Recommended Products

View More View Less

Find Similar Products By Category

Mechanical Parts & Fabrication Services > Motor > DC Motor
Categories
Hi~