0.6/1KV Power cable(IEC standard), description about High Quality Steel Wire Armoured YRY Power Cable on China Suppliers Mobile

Product Details

Specification for YRY Power Cable

Structure:

1. Copper Conductor, round soild, round stranded

2. Core insulation :PVC

3. Inner covering: Plastic tape

4. Sheath: PVC black

5. Armouring: Galvanized steel wires

6. Counter helix: Galvanized Steel Tape

7. Outer covering: plastic tape

8. Sheath: PVC black, UV resistant

Usage:

Power distribution cables in power stations, industrial installations and switchgear, as well as in local mains. Fpr fixed installation in interior premises, cable ducts, in the open air, in water- as permitted by the local building regulations-when high protection against mechenical damage is required.

Under ground cable with pvc inaulation pvc sheath

Usage: Power distribution cables in power stations, industrial installations and swithgear, as well as in local mains. For fixed installation in interior premises, cable ducts, in the open air, in water.

1. Conductors: copper or aluminum.

2. Both armored and non-armored type power cables are available.

3. Voltage rating: 0.6/1kV 3.6/6kV 6/10kV 8.7/15kV 26/35kV.

4. PVC or PE sheathed.

5. Number of cable cores: one core (Single core),two cores(Double cores),three cores,

Four cores (Four Equal-section-area cores or three equal-section-area cores and one smaller section area neutral core),

Five cores (Five equal-area cores or three equal-section-area cores and two smaller section area neutral cores).

6. Standards: IEC 60502.IEC, BS, DIN, ASTM, CSA, NFC, AS, GOST etc. Or other special characteristics as customers request.

1.Standard :

IEC60502,GB/T 12706

2. Specification:

Type	Designation	Application
VV	Copper conductor ,PVC insulated ,PVC sheathed power cable	For laying indoors, in tunnel or cable trench,unable to bear extermal mechanical forces. Single core cable is not permissible to lay in magnetic duct
VLV	Aluminium conductor ,PVC insulated ,PVC sheathed power cable
VY	Copper conductor, PVC insulated, PE sheathed power cable
VLY	Aluminium conductor ,PVC insulated ,PE sheathed power cable
VV22	Copper conductor ,PVC insulated ,steel tape armoured ,PVC sheathed power cable	For laying indoors, in cable trench or direct in ground ,able to bear external mechanical forces, but unable to bear pulling force
VLV22	Aluminium conductor ,PVC insulated ,steel tape armoured ,PVC sheathed power cable
VV23	Copper conductor ,PVC insualted ,steel tape armoured ,PE sheathed power cable
VLV23	Alunminium conductor ,PVC insulated ,steel tape armoured ,PE sheathed power cable
VV32	Copper conductor, PVC insulated, steel wire armoured,PVC insulated power cable	For laying indoors, in cable or direct in ground ,able to bear external mechanical forces, but unable to bear large pulling forces
VLV32	Aluminium conductor, PVC insulated ,steel tape armoured ,PVC sheathed power cable
VV33	Copper conductor, PVC insulated steel wire armoured , PE sheathed power cable
VLV33	Aluminium conductor , PVC insulated , streel wire armoured ,PE sheathed power cable
Note: The armoured single core cables is only used for D.C.system. As for A.C.system,non-magnetic armored material should be applied

3. Nominal Cross-sectional Areas:

1.5 mm², 2.5 mm²,4 mm², 6 mm², 10 mm², 16 mm²,25 mm², 35 mm², 50 mm²,70 mm², 95 mm²,120 mm²,150 mm²,185 mm²,240 mm²,300 mm² 400 mm² 500 mm² 630 mm² 800 mm²

4. Production Range:

single core cable from 1.5 mm²to 800 mm²,muli-core cable from 1.5 mm² to 400 mm²

5. Operating Characteristics:

Rated power-frequency voltage u0/u:0.6/1 KV

Max permissible continuous operating temperature of conductor 70

Max short-circuit temperature of the conductor shall not exceed (Max 5 seconds duration): cross-section of conductor 300 mm²

The ambient temperature under installations should not be below 0

The bending radius of single core cable should not be less than 20 times of the cable diameter ,the bending radius of multi-core cable should not be less than 15 times of the cable diameter.