Stainless Steel Soap Dispenser Soap Dispenser Behind The Mirror Soap Dispenser
Negotiable /Piece
Min.Order:10 Pieces
Zhongshan ACEYEA Sanitary Ware Co., Ltd.
Placed Behind The Mirror Liquid Hand Soap Dispensers Concealed Soap Dispenser
Foaming Soap Dispenser Electric Dish Soap Dispenser Large-capacity Mirror Soap Dispenser
Electric Hand Soap Dispenser Liquid Bath Soap Dispenser Large-capacity Mirror Soap Dispenser
Commercial Soap Dispenser Bath Soap Dispenser Wall Mount Tray And Soap Dispenser Behind The Mirror
Suitable For Families And Hotels Electric Hand Soap Dispenser Sensor Liquid Soap Dispenser
Specification:
1) Automatic on/off: Soap dispenser automatically supplies foam soap as the dispense-time set as soon as hands in sensor range. Soap dispenser automatically stops working if hands out of sensor range..
2) Adjustable sensor range and soap volume by a remote controller (optional).
3) Low power indication: Soap dispenser sensor flash to indicate that it is time to replace existing batteries with new ones if there is not enough power going to the unit. No soap dispensed at this time if hands in the sensor range.
4) Four D-type alkaline batteries shall last approximately 3000 times/month for 6 months.
5) It is suggested cleaning the soap hoses with clean tap water if you will not use the soap dispenser for more than 1 week. How to clean: please pour clean tap water into the soap bottle and sense the soap dispenser until the tap water dispensed.
How to clean soap dispenser on automatic he washing machine
On a front load washer, you can remove the washer detergent drawer by pushing in on the ends of each side of the drawer at the same time and then pulling it out. On a top load washer, pull the drawer out, and then tip it up to remove it.
Description:
1 it can match and use together with all kinds of faucets perfectly.
2.It adopts the infrared ray emission and reception technology, which is completely touch-free so that it is convenient and safety.
3.The spout is made of brass plated with chrome and its plating is enhanced, so that the product can maintain a long term fresh color and become more durable.
4.Time-adjustable and amount-adjustable, the users can adjust the dispensing time and foam amount, and it can be used in various
How to repair automatic soap dispenser
1. First of all, the water supply pipe leaks. First, close the angle valve, remove the hot and cold water pipe, and check whether the rubber pad is aging and whether the screw is loose.
2. If the angle valve or hot and cold water pipe is damaged and rusted, only replace it with a new one.
3. Water tank leakage, may be the tank stainless steel plate is damaged, or the sink of the water pipe and the connection of the water device leakage.
4. If the water tank is damaged, the hole less than 2 mm can be directly smeared with waterproof putty; if the leakage is less than 5 mm, it is recommended to use white iron sheet to make splint, and the middle should be coated with waterproof putty. If the hole is larger, it is recommended to replace it with a new one.
5. In case of water leakage, remove and carefully check whether the rubber pad is aging or not, and the gasket is not functioning properly.
6. If it is the water pipe leakage, you can check whether the screw buckle is loose and whether the water pipe is aging
7. If the down pipe is aged, the general method can not be blocked, so it is recommended to replace it with a new one.
Products Features:
●Humanized appearance design, convenient installation design and simple liquid adding design.
●Adaptive or adjustable sensing technology.
●Exclusive development of soap pump technology, can automatically stop reflux.
●Optional AC/DC power supply.
●1000 ml liquid storage bottle.
●Suitable for soap solution viscosity: 100-3800cPs.
●Including necessary installation hardware.
●Meets ASME A112.18.1/CSA B125.1 standard.
●Meets US ADA regulations and CJ/T 194-2004 standards.