sandblasting room designed by QINGGONG Machinery can complete a wide range of blasting jobs for those big and irregular workpieces. Traditional sandblasting equipment design can't be used to deal with parts in different shapes. However, our sandblasting room design is completed by professional engineers with rich experience. Our objective is to meet customers continuing demands for sandblasting business. The sandblasting room can blast big and irregular workpieces from all angles and make them clean. We want to make sure that our sandblasting room for sale can perform your job efficiently and economically.

Sandblasting Room Body

The wall of the sandblasting equipment body uses a noise attenuation sandwich panel with glass wool interlayer and abrasion-resistant rubber liner. The rubber liner also has the noise attenuation function.

The sandblast room wall is strengthened by welded strong square tubes which ensure they will not deformation during transportation and installation. The grinding and the painted square tube will be far enough to resistant the corrosion by the natural environment.

The cargo door and roof are built-in welded profiles and have closed in steel plates, and it internally assembled with abrasion-resistant rubber (up to 5mm). an exclusive sealing system prevents the loss of abrasive materials and makes the closing of the doors possible without effort.

Light fixtures use high efficiency LED lamps, which enables maximum utilization of the luminosity. The fastening system of the blasting room allows easy removal for maintenance.

Sandblasting Room Machine

The sandblasting rooms system adopts the most advanced venturi blast nozzle. For the venturi nozzle, a new combination of aluminum and polyurethane adds proven advantages in weight balance, strength and shock absorbent features not found in metal cased nozzles. The long venture design of the abrasive sandblasting machine will maximize production requirements as well as give added abrasive impact when needed for tough, hard to clean surfaces.

Sandblasting Room Installation Instruction & Safety Operation Manual

Abrasive Recovery System of Sandblasting Room

The abrasive recovery system for blasting room have 4 parts: floor recovery, bucket elevator and separator.

Sandblasting reclaim system use floor recovery system to reclaim the used blasting media and contaminants into the bucket elevator and then into the air wash cleaner system, and then the cleaned abrasive get into the storage hopper to recycle, the residual will get our of the recycle system from the separator.

Sweep/Shovel Chute Type

Sweep/ shovel chute type is the most economical abrasive reclaim system, which is only appropriate for low production operations.

This is the simplest reclaim system, but need to push the abrasive into the recycle system manually after blasting work.

This blasting room recovery system almost no need foundation pit, no damage to the ground.

Single Screw or Scraper Partial Reclaim System

The most economical floor design is available. The system contains a screw conveyor or craper conveyor, heavy-duty screw belt and bucket elevator,air-wash separator, perforated plate rotary drum separator and oversized abrasive storage hopper with a caged man ladder and handrail. This can be expanded to an "H", "U", or full floor reclaim system, which is best suited for low to medium production levels.

"L"- Shaped Partial Reclaim System

Adds one longitudinal conveyor along one sidewall of the blast room allowing the abrasive delivered from the blasting nozzle, which is either blown or rebounded off the workpiece, to strike the side walls and fall into the conveyors, automatically reclaiming approximately 40-70 percent of the blast media. The reclaiming abrasive on the blast booth floor is pushed into the screw or scraper conveyors assemblies at the end of the work shift. The "L" shaped floor design is typically used in a “flow-through” room configuration where heavy workpieces and/or material handling devices can drive into the room. This is best suited for low to medium production.

"H" - Shaped Partial Reclaim System

Adds two longitudinal conveyors along each sidewall of the sandblast room allowing the abrasive delivered from the blasting nozzle, which is either blown or rebounded off the workpiece, to strike the side walls and fall into the conveyors, automatically reclaiming approximately 60-90 percent of the blast media. The reclaiming abrasive on the floor is pushed into the screw or scraper conveyors assemblies at the end of the work shift. The “H” shaped floor design is typically used in a “flow-through” room configuration where heavy workpieces and/or material handling devices can drive into the room. This is best suited for medium to high production.

"U"- Shape Partial Reclaim System

Adds two longitudinal screw or scraper conveyors assemblies along each wall of the blast room and positions the cross screw or scraper conveyors along the back wall of the blast room. This allows the abrasive delivered from blasting nozzle, which is either blown or rebounded off the workpiece, to strike the sidewalls and back wall of the blast room and fall into the reclaim system, A “U”- shaped floor design will automatically reclaim 60-90 percent of the blast media. The remaining abrasive on the floor is pushed into the metered shed plate screw assemblies at the end of the work shift, The “U”-shaped floor design is typically used in an “in-out” room configuration where heavy workpieces and/or material handling devices can drive into the room. This is best suited for medium to high production

Full Floor Partial Reclaim System

The full-floor reclaim system utilizes multiple screw assemblies or scraper assemblies to create a fully automatic, high volume abrasive reclaim system where 100% of the abrasive blast media is returned to the separator system during the blasting operation. This allows for a faster reclaim as well as full recycling of the abrasive media, saving your blasting operation both time and money.

The Full Floor Reclaim System allows for the maximum efficiency of your abrasive blast system. This abrasive blast reclaim system is well suited for pass-thru and/or high production requirements.

Dust Collector of Sandblasting Room

The dust collector is one of the most important components of the sand blasting booth. QINGGONG MACHINERY’s cartridge dust collector are sized to fit each individual room according to room size, parts being blasted, amount of dust from the blast media and airflow.

Shot Blasting Machine

QINGGONG MACHINERY shot blasting machine offers you an effective solution to deal with the surface of the workpieces, including remove the contaminant on the surface, clean and roughen a smooth surface before applying a primer or coating to the workpiece. More specifically, the treatment of a shot blasting machine includes derusting, descaling, desanding, or deburring of the workpieces. Other uses are such as surfaces shot peening, finishing, and roughening of surfaces so as to make coat better.

As the shot blasting machine manufacturer, QINGGONG MACHINERY mainly supplies four types of partial reclaim systems, including sweep-chute floor, single screw, H-shaped partial reclaim system, and U-shape partial reclaim system.

QINGGONG MACHINERY also offers a full spectrum of blast room reclaim floor designs and configurations. Our full floor reclaim system requires merely a shallow concrete foundation. The type of sandblasting room is carefully designed to lift working effiency.