RF Flange

PRODUCT DESCRIPTION

Rf flange sealing surface is a plane, and the gasket contact area is large, after pre-tightening, the gasket is easy to extend to the two sides or move, poor sealing, only suitable for low-pressure occasions.

Rf flanges are mostly used in cases with mild medium conditions, such as low-pressure non-purified compressed air and low-pressure circulating water. Medium temperature and pressure are not high and medium corrosive. When the medium is highly corrosive, the flange contact medium part (flanged short section) for corrosion resistant high grade materials such as stainless steel, and the external use of lower materials such as carbon steel flange ring clamping it to achieve sealing.

Name: RF Flange

Size: 1 / 2" - 36"

Material: All kinds of carbon steel,such as A105 / A234WPB / Q235

Pressure: Sch20 / 40 / 60, STD as need.

Type: carbon steel, welded

Packaging: Wooden cases or as per customers requirement

Application rang: Petroleum, chemical, power, gas, metallurgy, shipbuilding, construction, etc.

Standard: ANSIB16.9, GBT12459 / 13401, SH3408 / 3409-96, ASME DIN JIS BS GB / T JB SH HG

Others:

1. Special design available according to requirement

2. anti-corrosion and high-temperature resistant with black painting

3. Our company will be good and cheap products open an international market, meet your needs .

Pipe fittings are various, the category of pipe fittings as follows:

1. Enlarge center pipe fitting. As required, or the end portion of the tube portion to expand a tubular member formed of various shapes;

2. Fittings with crimping and head.

Various shapes of flange faces

more visit:

/carbon-flanges.aspx.html

/915734-4-in-x-2-in-reducing-tee-xs-high-yield-y52-carbon-steel.html

/flanges-79.html  

What is a Flange face?

If the flange surface refers to the flange plate, it is the connecting fitting of the metal pipe, which is welded vertically on the end of the pipe. After the two flange surfaces are aligned, connect them with bolts and nuts, and the pipe is connected.

Different types of flange faces are used as the contact surfaces to seat the sealing gasket material. ASME B16.5 and B16.47 define various types of flange facings, including the raised face, the large male and female facings which have identical dimensions to provide a relatively large contact area.

Other flange facings covered by these standards include the large and small tongue-and-groove facings, and the ring joint facing specifically for ring joint type metal gaskets.

Raised Face (RF)

The Raised Face flange is the most common type used in process plant applications, and is easily to identify. It is referred to as a raised face because the gasket surfaces are raised above the bolting circle face. This face type allows the use of a wide combination of gasket designs, including flat ring sheet types and metallic composites such as spiral wound and double jacketed types.

The purpose of a RF flange is to concentrate more pressure on a smaller gasket area and thereby increase the pressure containment capability of the joint. Diameter and height are in ASME B16.5 defined, by pressure class and diameter. Pressure rating of the flange determines the height of the raised face.

The typical flange face finish for ASME B16.5 RF flanges is 125 to 250 µin Ra (3 to 6 µm Ra).

Raised Face height

For the height measures H and B of all described dimensions of flanges on this website, with exception of the Lap Joint flange, it is important to understand and remember the following:

In pressure classes 150 and 300, the height of raised face is approximately 1.6 mm (1/16 inch). In these two pressure classes, almost all suppliers of flanges, show in their catalog or brochure, the H and B dimensions including the raised face height. 

In pressure classes 400, 600, 900, 1500 and 2500, the height of raised face is approximately 6.4 mm (1/4 inch). In these pressure classes, most suppliers show the H and B dimensions excluding the raised face height. 

Yihang Flat Face (FF)

The Flat Face flange has a gasket surface in the same plane as the bolting circle face. Applications using flat face flanges are frequently those in which the mating flange or flanged fitting is made from a casting.

Flat face flanges are never to be bolted to a raised face flange. ASME B31.1 says that when connecting flat face cast iron flanges to carbon steel flanges, the raised face on the carbon steel flange must be removed, and that a full face gasket is required. This is to keep the thin, bittle cast iron flange from being sprung into the gap caused by the raised face of the carbon steel flange.

Ring-Type Joint (RTJ)

The Ring Type Joint flanges are typically used in high pressure (Class 600 and higher rating) and/or high temperature services above 800°F (427°C). They have grooves cut into their faces which steel ring gaskets. The flanges seal when tightened bolts compress the gasket between the flanges into the grooves, deforming (or Coining) the gasket to make intimate contact inside the grooves, creating a metal to metal seal.

An RTJ flange may have a raised face with a ring groove machined into it. This raised face does not serve as any part of the sealing means. For RTJ flanges that seal with ring gaskets, the raised faces of the connected and tightened flanges may contact each other. In this case the compressed gasket will not bear additional load beyond the bolt tension, vibration and movement cannot further crush the gasket and lessen the connecting tension.

Tongue-and-Groove (T&G)

The Tongue and Groove faces of this flanges must be matched. One flange face has a raised ring (Tongue) machined onto the flange face while the mating flange has a matching depression (Groove) machined into it's face.

/