Pneumatic floating marine rubber airbag
Marine rubber airbags can be used in a wide range, the most important reason is that it is easy to operate. It has no special requirements which is less limited by the site, and do not need other large equipment. In this case, Marine air bag can greatly reduce construction costs and save a lot of cost.
Features
1.High resistance to pressure: When Marine airbag is put under the bottom of the ship, it is squeezed by the ship and the air. As a result of the uneven rotation rate, the airbag will change the spiral shape. Our products has high resistance to take the pressure to remain its shape.
2.Durable anti-aging and wear-resistant ability: Marine airbags are exposed to sunlight, fresh water, sand and other pollutants in a hard environment. Our products are durable in appearance, resistant to fresh water and chemicals, and resistant to aging.
3.Optimized layout: the strength model of inflatable airbag was established and the function test was conducted.
Features
1.High resistance to pressure: When Marine airbag is put under the bottom of the ship, it is squeezed by the ship and the air. As a result of the uneven rotation rate, the airbag will change the spiral shape. Our products has high resistance to take the pressure to remain its shape.
2.Durable anti-aging and wear-resistant ability: Marine airbags are exposed to sunlight, fresh water, sand and other pollutants in a hard environment. Our products are durable in appearance, resistant to fresh water and chemicals, and resistant to aging.
3.Optimized layout: the strength model of inflatable airbag was established and the function test was conducted.
Structure of marine rubber airbag
1. Airbag body
The airbagbody is composed by natural rubber and strength fiber material through vulcanization progressing
2. Terminal iron part
The terminal iron part is made of cast iron, it is combined closely with the airbag body, one end is for pulling when you move it, and the other end if for charging and discharging the air.
The airbagbody is composed by natural rubber and strength fiber material through vulcanization progressing
2. Terminal iron part
The terminal iron part is made of cast iron, it is combined closely with the airbag body, one end is for pulling when you move it, and the other end if for charging and discharging the air.
Specification
Marine rubber airbags launching type:
1. There are three arrangement to arrange air bags when using launching type.
They are:
(1) linear arrangement as show in Figure A.1
(2) staggered arrangement as show in Figure A.2
(3) two lines arrangement as show in Figure A.3
As for which arrangement to use, it needs to depend on the ship’s width and the length of the air bags.
2.The linear arrangement means that :If the vessel width is 12m and the airbags effective length is more than 12m, so you can use the linear arrangement.
3. The staggered arrangement means that: If the vessel width is 18m, and your airbags effective length is 12m, so you should use staggered arrangement.
4. The two lines arrangement means that:When the vessel is 24m width, your airbags is 12m length, you should use the two liners arrangement.
They are:
(1) linear arrangement as show in Figure A.1
(2) staggered arrangement as show in Figure A.2
(3) two lines arrangement as show in Figure A.3
As for which arrangement to use, it needs to depend on the ship’s width and the length of the air bags.
2.The linear arrangement means that :If the vessel width is 12m and the airbags effective length is more than 12m, so you can use the linear arrangement.
3. The staggered arrangement means that: If the vessel width is 18m, and your airbags effective length is 12m, so you should use staggered arrangement.
4. The two lines arrangement means that:When the vessel is 24m width, your airbags is 12m length, you should use the two liners arrangement.
Advantages of marine rubber airbag
1. Various sizes
2. Provide repairing kit
3. Long service life
4. Reused many times
5. Good wear resistance
6. Good raw material
7. Harmless to the enviroment
8. Cheaper and portable
2. Provide repairing kit
3. Long service life
4. Reused many times
5. Good wear resistance
6. Good raw material
7. Harmless to the enviroment
8. Cheaper and portable
The storage of marine rubber airbag
1.Marine rubber airbags should be maintained in a dry ventilated room and be protected from light
2.Marine rubber airbags should be in a relaxed condition free from tension, compression or other deformation.
3.Marine rubber airbags should be kept away from any heart source
4.Marine rubber airbags should be protected from acids, alkalis, oils or organic solvents.
2.Marine rubber airbags should be in a relaxed condition free from tension, compression or other deformation.
3.Marine rubber airbags should be kept away from any heart source
4.Marine rubber airbags should be protected from acids, alkalis, oils or organic solvents.
Application of marine rubber airbag
1. Ship Launching and Landing
2. On Land Construction
3. Ship Salvage
4. Objects Lifting
5. Caission Floating
6. Marine Engineering
2. On Land Construction
3. Ship Salvage
4. Objects Lifting
5. Caission Floating
6. Marine Engineering
Different layers of marine rubber airbag
Different sizes of marine rubber airbag