Motor type | Output Power | Voltage | Load | Speed | Rated Torque | Efficiency | Noise | IP Class |
KW | V | A | RPM | Nm | % | dB | ||
VOL-BL2K0B48 | 2 | 48 | 44.80 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B72 | 2 | 72 | 29.87 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B110 | 2 | 110 ac | 11.29 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B220 | 2 | 220 ac | 5.64 | 3000 | 6.37 | 93 | 62 | IP 54 |
VOL-BL2K0B380 | 2 | 380 ac | 3.27 | 3000 | 6.37 | 93 | 62 | IP 54 |
VIEW MORE PLS CONTACT US >>>
Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
You May Like
- EMP030 48VDC 600W 1800RPM brushless long bldc motor for racing
- EMP008 EV car 2500rpm 48v 1000w 3.82Nm 24.51Amp B3/B14/B34/B5 electric bldc brushless dc synchronous for electromobile
- EMP037 high voltage 3000rpm 220V 750W brushless dc motor BLDC
- High speed 4300rpm 45V 1550W brushless dc motor BLDC
- EMP040 48v 3000w 2650rpm pmsm with high power run a hammer mill
- EMP001 24V 250W 1700RPM 1.40Nm 12.25Amp B3/B14/B34/B5 Brushed brush bl DC motor for sale
- EMP002 hall 24V 1.2kw 1200W 1500RPM 7.64Nm 58.82Amp B3/B14/B34/B5 Brushless DC Motor for desert exploration
- EMP003 24V 3.6KW 3600W 3000RPM 176.47Amp 11.46NM B3/B14/B34/B5 Brushless DC Motor For air compressor
- EMP004 1kw 12V 1000W 1500RPM 6.37Nm 98.04Amp B3/B14/B34/B5 brushless dc BLDC Hall sensor for go-karting
- EMP006 72V 5500W 3680RPM 89.87Amp 14.27Nm B3/B14/B34/B5 Controller brushless BLDC for electromobile
Popular Searches
Find Similar Products By Category
You May Like
- EMP007 48V 4.8kw 4000W 2580RPM B3/B14/B34/B5 14.81Nm 98.04Amp controller hall sensor for electric vehicle car
- EMP008 48V 1kw 1000W 2500RPM BLDC controller for electric car
- EMP009 24V 750W 3000RPM No controller hall sensor brushless bldc motor for traction drive
- EMP010 48V 3kw 3000W 1500RPM 19.1Nm 73.53Amp B3 B14 B34 B5 hall sensor bldc Brushless DC Motor
- EMP011 24V 3600W 3000RPM 11.46Nm 176.47Amp Controller B5 bldc brushless dc motor for traction drive
- EMP012 48V 2.5kw 2500W 3000RPM 7.96Nm 61.27Amp B3 B14 B34 B5 traction system brushless dc BLDC motor with Hall sensor
- EMP013 72V 4kw 4000W 2580RPM 65.36Amp 14.81Nm eB3 B14 B34 B5 lectro-tricycle BLDC brushless dc motor with controller
- EMP014 12V 600W 1800RPM 58.82Amp 3.18Nm B3 B14 B34 B5 controller BLDC Hall sensor for Oil pump field
- EMP015 24V 1.5kw 1500W 2000RPM 7.16Nm 73.53Amp Hall sensor controller brushless bldc motor with Automotive air conditioning
- EMP023 230Vac 3000W 3000RPM 15.35Amp 9.55Nm B3 B14 B34 B5 temperature sensor brushless bl dc BLDC motor
- EMP024 24V 1500W 3500RPM 73.53Amp 4.09Nm B3 B14 B34 B5 Hall sensor controller brushless bl dc BLDC motor for dirt catcher
- EMP025 24V 1kw 1000W 1500RPM 49.02Amp 6.37Nm Hall Sensor BLDC brushless dc motor for vacuum pump
- EMP021 Customized flange shaft 48V 3kw 3000W 1500RPM 73.53Amp 19.1Nm controller brushless bldc motor for tracking system
- EMP022 230Vac 3000W 1500RPM 15.35Amp 19.1Nm B3 B14 B34 B5 temperature sensor controller BRUSHLESS BL DC BLDC MOTOR
- EMP026 12V 375W 3000RPM 36.76Amp 1.19Nm B3 B14 B34 B5 Hall sensor bldc brushless dc motor for electronic accessories