Motor type | Output Power | Voltage | Load | Speed | Rated Torque | Efficiency | Noise | IP Class |
KW | V | A | RPM | Nm | % | dB | ||
VOL-BL2K5A48 | 2.5 | 48 | 56.00 | 1500 | 15.92 | 92 | 62 | IP 54 |
VOL-BL2K5A72 | 2.5 | 72 | 37.34 | 1500 | 15.92 | 92 | 62 | IP 54 |
VOL-BL2K5A110 | 2.5 | 110 ac | 14.11 | 1500 | 15.92 | 92 | 62 | IP 54 |
VOL-BL2K5A220 | 2.5 | 220 ac | 7.05 | 1500 | 15.92 | 92 | 62 | IP 54 |
VOL-BL2K5A380 | 2.5 | 380 ac | 4.08 | 1500 | 15.92 | 92 | 62 | IP 54 |
VIEW MORE PLS CONTACT US >>>
Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
You May Like
- IEC 220v 3000rpm 60 hz synchronous motor PMSM electric motor
- IEC 1/4 HP 1500rpm 220v permanent-magnet synchronous brushless DC motor
- IEC 3hp 200w 1500rpm synchronous ac fan motor
- IEC 3000rpm 200w permanent-magnet synchronous brushless DC motor
- Wholesale IEC 2HP 1500w 220v 60hz phases permanent magnet synchronous brushless DC motor
- IEC 1/2HP permanent-magnet synchronous brushless DC motor PMSM
- Custom IEC 200w high eddiciency ACBrushless permanent magnet dc synchronous motors synchronous for sale
- IEC 1HP 220v 750W 3000rpm synchronous motor PMSM motor China
- Custom IEC low rpm 200w rotor neodymium dc permanent magnet synchronous brushless dc motor
- IEC 3000rpm 220v 200w permanent-magnet synchronous ac brushless DC motor
Popular Searches
Find Similar Products By Category
You May Like
- IEC 200W 110V Permanent Magnet Synchronous Motor
- IEC 5HP 3 phases synchronous PMSM brushless DC motor China
- IEC 1HP 220v synchronous PMSM brushless DC motor China
- IEC 220v 750w synchronous PMS Brushless DC motor
- 10000rpm 12v 48v 850w 2000w 48v 3kw high torqu winch control brushless dc motor kit for toy car
- IEC 2HP 3 phases synchronous PMSM Brushless DC motor from china
- 1600 watt 50 60hz 1hp 80m 750w 0.75kw synchronous three phase elektro electric brushless dc motor
- IEC 1HP synchronous PMSM Brushless DC Motor China
- Wholesale IEC 1/4 HP 1500rpm neodymium permanent magnet price dc motors brushless synchronous motor
- IEC 60Hz 200w 110v 240v permanent magnet synchronous motor
- Wholesale China IEC 1HP synchronous neodymium permanent magnet price brushless DC motor
- IEC 5HP 3 phases synchronous brushless DC PMS motor
- E-1 S1 12v 1000w 1500rpm BLDC hall sensor brushless dc motor
- E-3 S1 IP54 24v 3600w 3000rpm brushless dc motor with hall sensor
- E-4 48V 3000W 1500RPM customized flange shaft dc brushless motor