900Mbps 5G Outdoor CPE Router PTP 10KM Range Wi-fi Access Point WDS Wireless Wifi Bridge Extender Wifi Repeater For IP Camera
Main Features
■ Outdoor weatherproof protection design, Two Ethernet Ports
■ Qualcomm Chipset, 802.11ac/a/n Support
■ 128MB SDRAM + 16MB Flash Build-in for Higher Performance
■ Gateway / Repeater / AP /WISP Client/WDS/AP+WDS operation modes
■ S-WDS Mode, Advanced Software Technology, PTP/PTMP connection
■ 24V Passive PoE supports up to 70 meter (200 feet) deployment
■ 18dBi 5GHz directional MIMO panel antenna to build long distance Wi-Fi connection
■ Equipped LED display, show operation mode, channel, signal strength
Descriptions
OAP890 is a high power industrial 5G outdoor CPE with the next generation 802.11ac Wi-Fi standard, Qualcomm Chipset, combined 900Mbps high speed in 5G, equipped Gigabit WAN/LAN port, 3 times Ethernet data rate faster than other general cpe, make more than 60 end users access into it and enjoy seamless HD movies, streaming, online gaming, wireless security and other bandwidth-intensive tasks.
900Mbps Data Rate & Gigabit WAN/LAN Ports
OAP890 features 802.11ac Wi-Fi and 2*2 MIMO technology, 900Mbps wireless speed. Equipped with Gigabit Ethernet port ensures high speed internet access and more end users access.
10KM PTP/PTMP Distance
Designed in two line Power Amplifier on PCB board, the power can be 500mW high power, 18dBi MIMO high gain panel antenna, greatly increase the wifi range to 10KM distance, then supply the stable wifi signal for users.
Power over Ethernet
OAP890 has integrated passive Power over Ethernet (PoE), for easy installation and lower cost. So it can be installed in areas where power outlets are not readily available, eliminating the mess of altering existing network infrastructure.
Multiple operation mode, Press WDS Switch button(F&S) to do PTP/PTMP Connection
OAP890 supports Gateway, WISP, Wireless AP, WiFi Repeater, WDS operation mode, it is widely used in WiFi Bridge Connection, WISP Connection and Wireless Security;
OAP890 with WDS Switch button, press it to do the PTP/PTMP connection, very easy, no need to access into GUI.
Access Controller System
With Access Control System under AP/WDS operation mode, easily access advanced network settings through PC, like AP status monitor, change IP address, ESSID, Channel, Password, upgrade firmware, backup and restore.
Specifications
| Hardware: | |
| Chipset | Qualcomm QCA9563+QCA9882+QCA8334 |
| Standard | 802.11ac/a/n, MIMO technology |
| Memory | 128MB DDR2 RAM |
| Flash | 16MB |
| Interface | 1 * 10/100/1000Mbps RJ45 WAN Port |
| 1 * 10/100/1000Mbps RJ45 LAN Port | |
| 1 * WDS switch button(F&S), press it to do WDS PTE/PTMP connection | |
| 1 * Reset button, press 15 seconds to revert to default setting | |
| Antenna | Build in 18dBi MIMO Panel Antenna |
| Power consumption | 24V PoE,<8W |
| Size | 315mm * 145 mm * 80mm |
| RF Data | |
Frequency | 5GHz: 802.11a/ac |
| 5GHz: 5180~5825MHz | |
| Throughput | 900 Mbps |
| Country code | FCC,IC,ETSI,MKK,MKK1,MKK2,MKK3,NCC,RUSSIAN,CN |
| Modulation | OFDM = BPSK,QPSK, 16-QAM, 64-QAM |
| DSSS = DBPSK, DQPSK, CCK | |
| Receive Sensitivity& RF Power | |
| RF Power | 802.11a:54M 23±2DB,6M 26±2DB. 802.11n HT20:MCS7 23±2DB, MCS0 26±2DB. 802.11n HT40:MCS7 22±2DB, MCS0 25±2DB. 802.11ac HT80:MCS9 20±2DB, MCS0 23±2DB. |
| Receive Sensitivity | 802.11a: -72dbm@54Mbps; -90dbm@6Mbps. 802.11n HT20: -70dbm@MCS7, -90dbm@MCS0 . 802.11n HT40: -66dbm@MCS7, -90dbm@MCS0 . 802.11ac HT80:-60dbm@MCS9, -86dbm@MCS0 . |
| EVM | 802.11n: ≤-28 DB 802.11a: ≤-25 DB |
| Firmware Features: | |
| Operation mode | Wireless AP, Gateway, WISP, WiFi Repeater, WDS |
| WAN Type | Dynamic IP/Static IP/PPPoE/L2TP(Dual Access) /PPTP(Dual Access) |
| Wireless Security | 64/128-bit WEP, WPA / WPA2, WPA-PSK/ WPA2-PSK encryption |
| SSID | Multiple SSID up to 4 |
| Firewall | DoS, SPI Firewall, IP Address Filter/MAC Address Filter/Domain Filter IP and MAC Address Binding |
| Protocols | IPv4 |
| Others: | |
| Package Contents | 1x 900Mbps 11AC wireless access point 1x Ethernet Cable 1x PoE Adapter 1x User Guide(E-book English Instruction can send by msg!) 1x Setting Accessory |
| System Requirements | Microsoft Windows 98SE, NT, 2000, XP, Vista™ or Windows 7, Windows 8, MAC OS, NetWare, UNIX or Linux |
| Environment | Operating Temperature: -44~55 ℃ Storage Temperature: -40~70 ℃ Storage Humidity: 5%~90% non-condensing |
| Management | Firmware GUI ,Remote Management, WLAN Controller, Cloud Management System |
