CY-CNC-8 4228 s series l multi-functional  machine

technical parameters:

1), loading size range: Maximum size: 4200*2800mm

2), upper blade and cutting thickness: 3~19mm

3), the fastest on the film cycle: 40-50 seconds

5), the maximum depth of suction: 700mm (according to the need to be special development)

6), the biggest piece of attached load: 600KG

7), the number of unilateral upper arms: 3 arms

8), single sucker number: Three

9), on the flip arm: single

10), installation Power: 50HZ / 380V (special circumstances can be adjusted according to customer requirements)

11), installation Power: about 11KW

12), compressed air: 0.5~0.7Kpa

13), vacuum pressure: 0.5-0.9Kpa (according to the thickness of the glass can be adjusted)

14), Y axis conventional walking speed: 5m / min (frequency conversion)

15), mesa height: 900 + 20mm

16)cutting Accuracy: ≤±0.2mm

2.machine configuration

1), loading table chain: high precision.

2), transmission roller: PU material.

3), vacuum chuck: rubber material

4), main bearing: Japan NSK

5), transmission belt / pulley: Italy Babeli

6), American imported PU plate

7), linear guide: HIWIN

8), cutter wheel / cutter: Germany

9), table: imported industrial felt (black)

10), rack: GUDEL

3 electrical components:

1), PLC controller: Taiwan (Delta) or Japan ( MITSUBISHI )

2), delta inverter: Taiwan (Delta)

3), touch screen: Taiwan (Delta)

4), photoelectric switch: OMRON

5), other electrical appliances: Schneider

6), control cable: shielded cable

7), pneumatic components: the main original use of Japanese SMC / other

8) Motor:Yaskawa

4 Only need small place for the equipment , easy to operate,high speed and high accuracy and artificialIt Is suitable for

the construction windows and doors, the lens, the craft, the decoration, the coating and so on glass cutting operations,

the concrete introduction is as follows:Mainly used in the automatic glazing of glass, automatic composing and breaking

function and automatic unloading glass system.

The whole working process of PLC automatic control and motion control card control or manual control can be

completed. Manual mode is mainly used in equipment adjustment and maintenance, each action can be completed

alone, can also be used for normal work. Is to take a signal (manual and automatic), flip, work system, motor drive

mechanical reverse mechanism the sucker arm turned up, tilt angle and reach and glass like flip to stop, before moving

motor drives the moving body, when the suction cup at the top near the detection switch contact to glass, advancing the

motor stop. Vacuum system work, the suction cup began to absorb the glass, when the vacuum pressure switch to set

the pressure, the sucker rod mechanism driven by the motor to the glass, in this position after about a few seconds, to

ensure that the single glass, motor driven mechanical reverse mechanism to make the glass and glass at the same time,

and then the whole frame automatically find zero position, the surface of the wind machine can easily move the glass

knife designated place for the next action (cutting function). In automatically to sucker blow on the glass onto the table,

cutting machine is started automatically border patrol, cutting.

5. technical description:

1), flip mode and suction mode:

Mechanical flip, flip angle can be adjusted. Fast running speed, good stability, can be achieved 3~19mm all kinds of

thickness of glass automatically take a piece, flip arm with connecting rod device, suction depth of up to 700mm.

2), sensing device: all sensing devices use two sets of sensors, which can ensure the safe and stable operation of the

equipment.

3), vacuum suction: adsorption device, double chain transmission

4), alarm device: with automatic detection device, the abnormal situation can automatically alarm and display. With

emergency stop switch, it can be controlled in the presence of abnormal.

5), operation mode: automatic mode and manual mode of two kinds of functions for selection, easy to operate.

6), the operation interface: the LCD touch screen display interface, Chinese display module, the operation is convenient

and fast (can be installed in English language interface)

6.Cutting software

1.Professional supporting cutting system and cutting optimization software.

2: with a variety of cutting Library (easy drawing and operation) CAD AUTO drawing software is compatible (direct input

cutting glass size, automatic optimization of direct cutting)

3: has the function of automatic correction. Ensure cutting accuracy.

4.The cutting path selection function. Make sure to reach the best cutting speed.

5.The origin: correction function. Can set the origin two times

6: operation input: keyboard and mouse. Chinese / English dialogue interface

7.The cutting knife: a pressure automatic regulating function, to ensure the best effect of cutting