BD-FE1-4ETH-M E1 to 4*100BASE-TX ethernet Protocol converter is high performance Ethernet bridge, which accomplishes the 4*100M Ethernet over E1 transmission.  As an extended device of the Ethernet, the E1 to 4*ethernet protocol  converter realizes interconnection of four Ethernet by using the E1  channel provided by existing networks with low cost.

10/100Base-T(RJ45)  interfaces are provided at the end of Ethernet LAN to accomplish  various functions including MAC address self-learning, address  filtering, address table maintenance and flow control.

The E1/4*10/100BASE-TX converter support GUI NMS through console port.  User can easy set the four Ethernet as shared mode (intelligent L2  switch) or isolation mode(based on port and TAG vlan). In the VLAN  mode,user can set the TAG VLAN on these 4 ethernet port, can set the  special tag like Q-in-Q, can configurable data rate from 32K~100M on each ETH port, can do some Qos setting.

The  E1 to 4ethernet converter’s E1 interfaces comply with ITU-T G.703 and  G.704 standards. The E1 interface support 120ohm (RJ45 connector) and  75ohm (BNC connector). The E1 ports support both framing and unframing  architecture.The user can select an operating mode for the E1 interface  according to the connected E1 environment. This provides flexibility of  network application. In the framing mode, the E1 interface provides a  rate of N*64Kbps（N=1~31）. In the unframing mode, the E1 channel provides a rate of 2.048Mbps and accomplishes transparent transmission. 

FE1-4*100BASE-TX  protocol converter is used in the framing mode, the transmission clock  can be either provided internally, i.e. using the main clocking timing  mode (INT), or extracted from the E1 channel, i.e. using slave clock  timing mode.

FE1-4*100BASE-TX  protocol converter provides plenty of self-test functions, supporting  local loop and remote loop. It also provides pseudo random code test  function to test error codes in the circuit.

Features:

²       In accordance with the provisions of IEEE 802.3u、IEEE 802.1q、IEEE 802.3x、ITU-T G.703、G.704 and G.823 protocols.

²       E1 interface support framed and unframed mode;

²       E1 support balanced 120ohm(RJ45 conncetor) and unbalanced 75ohm (BNC connector).

²       The E1 interface uses PCM31 mode, supporting CRC check.

²       E1 interface main/slave clock optional in the framing mode.

²       Supporting 2.048Mbps transparent transmission in the E1 unframing mode.

²       The 10/100Base-T Ethernet interface supports 10/100M half/full duplex modes.

²       Ethernet port support isolation based on port and tag VLAN (16 VLAN).

²       The rate of each Ethernet port is measured by the configuration software, bandwidth particles for 32 k.

²       Each Ethernet port support broadcast storm protection, PAUSE flow control.

²       MAC address self-learning and address filtering functions, reducing the transmission load of the E1 circuit.

²       Built-in  64Mbits SDRAM Ethernet data buffer memory, improving the capability of  Ethernet side anti-outburst, assuring high throughput of data  transmission.

²       E1 circuit remote loop and local loop tests.

²       Perfect circuit test and alarm indication.

²        Support local console network, can be set up on the Ethernet port.

E1 Interface

Ø         Line Rate:

framing: N*64Kbps，N=0~31; unframing: 2.048Mbps

Ø         Line Code : HDB3

Ø         Interface Standard: ITU-T G.703

Ø         E1 Impedance: 75Ω(unbalance) BNC connector and 120Ω(balance) RJ45 connector

Ø         Jitter tolerance : comply with G.823,  Output jitter <0.05UI

10/100Base-T Ethernet Interface
Rate: 10/100M, full/duplex auto-negotiation
Protocol: Support IEEE 802.3,IEEE 802.1Q (VLAN)
MAC Address Entiries: 4096 Entiries
Total Memory Sizes: 64MBits SDRAM
Physical interface: RJ45, support AUTO-MDIX
 

Power supply                         

working voltage range wide, good        

anti-disturb and Isolation, work stable     

option I – DC-48V,range DC-36V~DC-72C   

option II – AC220V,range AC165V~AC240V

Power Consumption:    <=5 Watts 

Environment condition                  

Operating temperature:  0C~+50 C        

Storage temperature:   -20 C~+70 C

Relative temperature:95% (uncondensed)

Dimension                  

²       210mm(L)

²       140mm(W)

²        40mm(H)

Application
 

Application1:Share Link mode:

Each  LAN can view and communicate with other LANS, for example LAN A1 can  communicate with LAN A2 LAN A3 LAN A4 and LAN B1 LAN B2 LAN B3 LAN B4

Application2: Isolation mode:

Ordering information